User manual YAMAHA CRW4261T

[. . . ] CRW4261t SERIES User Guide Guide de I'utilisateur Bedienungsanleitung COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW4261t CRW4261t-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] ATAPI provides high-speed transmission of large quantities of data, which is especially important when working with image data. s Orange Book Part 2, Part 3 Compatible 5-Mode Recording The CRW4261t conforms to the five recording modes outlined in the Orange Book Part 2 and 3: Track at Once, Multisession, Disc at Once, Session at Once, and Packet Writing. 1 Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CDROM drives other than a CD-RW or a CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not possible to write additional data later. Session at Once In this mode, data can be recorded to disc one session at a time. To use this mode, your software must support Session at Once recording. Packet Writing This is useful for data back-up. Smaller units of data can be added to tracks. To use this mode, your software must support Packet Writing. The CRW4261t supports both sequential and random packet writing. 2 Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4261t, make sure that you have all of the items on the list of included items. In order to use the CRW4261t, you will require the following. Computer The following operating environment is required: · An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed), or a 100 MHz or faster 486 CPU (in order to write at 2x speed) · A vacant IDE interface connector · A vacant half-height bay · Windows 95, Windows NT4. 0 or Higher · Sufficient hard disk space Note: You will need about twice as much space on your hard disk as that required by the data you wish to write to CD-ROM. Software Use writing software or packet writing software which supports the CRW4261t. Tools Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW4261t drive. Long nose pliers These are used to insert or remove the jumper pin when setting the MASTER/SLAVE settings of the Yamaha CRW4261t drive. Long nose pliers Phillips Screwdriver 3 Chapter 1 - System Configuration Discs On the CRW4261t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R (120mm, 74 minutes) CD-R Discs > CDM12Y74M (120mm, 74 minutes) > CDM12Y74T (120mm, 74 minutes) Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-ROM standard, Yellow Book). If you wish to use the audio functions, use discs with the logo, which conform to the Compact Disc Digital Audio standard (Red Book). 4 Chapter 2 - Installing the Yamaha CRW4261t Drive Chapter 2 - Installing the Yamaha CRW4261t Drive MASTER/SLAVE settings Before you install the CRW4261t in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4261t drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin. Rear Panel AUDIO OUT RGL CSEL SLAVE MASTER IDE INTERFACE CONNECTOR DC INPUT +5V G +12V 1 Jumper Switch Enhanced IDE compatible computers normally have two IDE interface connectors; a primary one and a secondary one. Each IDE interface connector of the host computer allows up to two IDE devices to be connected. This means that a total of up to four IDE devices can be connected. [. . . ] Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction. ) Press the eject button If the CRW4261t is not powered on: Pressing the eject button will not eject the disc. 14 Chapter 3 - Operation Manual Eject (emergency use) Here we explain how to eject the disc when it cannot be ejected in the normal way; for example, the power is shut off inadvertently or the loading mechanism fails. This technique should be used only as a last resort. You'll need a pin-like object of 2 mm or less in diameter to do this. [. . . ]