User manual YAMAHA CRW4416SZ

[. . . ] SERIES User Guide Guide de l'utilisateur Bedienungsanleitung ON/ DISC READ/ WRITE Deutsch Français CRW4416S English COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW4416S CRW4416S-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] To use this mode, your software must support Packet Writing. The CRW4416S supports both sequential and random packet writing. 2 Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4416S, make sure that you have all of the items on the list of included items. In order to use the CRW4416S, you will require the following. Computer The following operating environment is required: · An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed) · A vacant slot in which to install a SCSI card or a pre-installed SCSI card · A vacant half-height bay · Windows 95, Windows 98 or Windows NT4. 0(Service Pack 3) · Sufficient hard disk space Note: If you wish to create an image file and write it to a CD-R or CD-RW, you will need approximately 750 MB of free space on your hard disk as work area. SCSI card This is required in order to connect a SCSI device (the Yamaha CRW4416S) to your computer. We recommend the following : Adaptec SCSI cards: AHA-2940 (PCI), AHA-154x (ISA) Software Use writing software or packet writing software which supports the CRW4416S. For software-related questions, please read the owner's manual for your software. 3 Chapter 1 - System Configuration Tools Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW4416S drive. Long nose pliers These are used to insert or remove the jumper pin when setting the SCSI ID and parity settings etc. of the Yamaha CRW4416S drive. Long nose pliers Phillips Screwdriver Discs s CD-R discs Please use discs that are compliant with Orange Book Part 2. (If you wish to write data at 4X speed, you must use discs which support high-speed writing. ) s CD-RW discs Please use discs that are compliant with Orange Book Part 3. (If you wish to write data at 4X speed, you must use discs which support 4X speed writing. ) Yamaha recommends the following Yamaha CD-RW discs: · CRWM74B4X (120mm, 74 minutes) · CRWM74R4X (120mm, 74 minutes) s Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-ROM standard, Yellow Book). If you wish to use the audio functions, use discs with the logo, which conform to the Compact Disc Digital Audio standard (Red Book). 4 Chapter 2 - Installing the Yamaha CRW4416S Drive Chapter 2 - Installing the Yamaha CRW4416S Drive CRW4416S drive settings Before installing the CRW4416S in your computer, you will need to set the following jumpers. · SCSI ID settings · Parity setting · Terminator setting · Block size setting This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4416S drive. Important: Use long-nose pliers to remove or insert jumper connectors. In the diagrams in this manual, solid black fill is used to indicate locations where a jumper is used to short between pins. Rear Panel ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI INTERFACE CONNECTOR 1 AUDIO OUT RGL 124 DC INPUT G + 5V +12V Jumper Switch s SCSI ID settings The SCSI ID number is used so that the computer will recognize a connected SCSI device. This function is valid only for workstations, such as those that run UNIX. Block size OFF (without a jumper) -- Normally, use this setting. Block size ON ID SELECT PARITY TERMINATOR BLOCK SIZE Block size OFF (default) ID SELECT PARITY TERMINATOR BLOCK SIZE 124 124 * Use jumper connectors to short the locations shown in black. 7 Chapter 2 - Installing the Yamaha CRW4416S Drive Installing the CRW4416S drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. (This user guide assumes that a SCSI card has already been installed. ) 1. Switch off your computer, and unplug it from the AC outlet. If you fail to do this, there is a danger of electric shock and/or of causing short circuits, which may damage the computer and/or CRW4416S drive. OFF PUSH 2. Be careful not to lose the screws that were removed. 8 Chapter 2 - Installing the Yamaha CRW4416S Drive 3. Your hands or body may be holding a charge of static electricity. [. . . ] This technique should be used only as a last resort. You'll need a pin-like object of 2 mm or less in diameter to do this. A straightened paper clip makes an ideal tool. Insert the pin-like tool into the manual eject hole and push gently. [. . . ]