User manual YAMAHA CRW8824EZ

[. . . ] FCC INFORMATION COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW8824E CRW8824E-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] AVA AESSA OLET AL TT TTIINA NÄKYVÄLLE JA / T AI NÄKYMÄTÖMÄLLE LASERSÄTEIL YLLE. VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETZEN. A TTENTION - RADIA TION VISIBLE ET / OU INVISIBLE LORSQUE L 'APPAREIL EST OUVERT . EVITEZ TOUTE EXPOSITION AU FAISCEAU. V565150-1 F Serial No. 8 Installation Installing the CRW8824E Drive You can install the CRW8824E drive in one of two ways: As an additional drive If the casing of your computer has a spare 5. 25-inch drive bay available, such as with many tower-type designs, you can install the CRW8824E drive in addition to the computer's existing CD-ROM drive. CRW8824E As a replacement drive If the casing of your computer does not have a spare 5. 25-inch drive bay available, such as with many desktop-type designs, you can replace the computer's existing CD-ROM drive with the CRW8824E drive. CD-ROM drive CRW8824E You cannot replace the computer's existing CD-ROM drive with the CRW8824E using the existing cable if the drive is a SCSI type. In this case, use an included IDE cable to connect the CRW8824E. 9 Installation Connecting the CRW8824E Drive The following steps explain how to install the CRW8824E as a secondary master on the tower computer for expansion or replacement. 1 Power down your computer and unplug it from the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/ or short-circuiting and damaging components, including the CRW8824E drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don't lose them. The method for removing the casing and fitting the drive in the drive bay can vary depending on the manufacturer. Refer to the documentation that came with your computer for further details. 3 Touch a metal part of the computer's Drain any static charge chassis or power supply unit to drain any static charge that may have built up inside your body. Alternatively, you can wear an anti-static grounding (earthing) wrist strap. You can permanently damage equipment if you touch it while there is any static charge in your body. 10 Installation 4 Remove the front cover of a vacant 5. 25-inch drive bay slot in the computer. When you finish this step, proceed to Step 7 on page 14. Additional Drive Front panel 5. 25-inch drive bay slot Front cover 4 Remove the front panel of the computer. Front panel Replacing Drive 5. 25-inch drive bay slot 11 Installation About IDE 1 IDE (Enhanced IDE/E-IDE) is one of the standards applied to the connection between personal computers and their peripherals. A computer motherboard provides two IDE connectors (primary and secondary). (Although, some motherboards provide only a primary connector. ) You may connect up to two IDE devices (hard disk, CD-ROM, or CD-R drives) to the connectors using an IDE cable. One of the devices connected via the IDE cable is called "master" and the other called "slave. " Additional Drive IDE connectors on the motherboard PRIMARY IDE IDE cable (primary) IDE device (slave) IDE device (master) SECONDARY IDE IDE cable (secondary) IDE device (slave) IDE device (master) 5 Disconnect all the cables connected to the rear of the existing CD-ROM drive, and also disconnect the audio cable from the sound card or motherboard's audio connector. The existing CD-ROM drive in the computer is assumed to be an IDE-type. Replacing Drive Audio cable ANAL OG AUDI O R GG L CABL E SLAV SELECT E MAS TER 39 40 HOST INTE RFAC E 1 2 PO +5V WER GG +12 V IDE cable 4-pin power connector 12 Installation About IDE 2 Yamaha recommends you connect only the CRW8824E as a secondary master. Example-1 IDE cable (primary) (slave) CD-ROM Drive e. t. c. (master) Hard Disk Remove the CD-ROM drive e. t. c. to replace it with the CRW8824E IDE cable (Secondary) Additional Drive If you disconnect the IDE device and re-connect it to another location, other devices connected to the IDE cable may become slow in processing, unstable, or inoperative. If the 40-pin IDE cable has only one connector available but you wish to re-connect the IDE device (that you just disconnected) to another location, use a 40-pin IDE cable that has two connectors. If you connect only one IDE device to an IDE cable, assign the device as a master and connect it to the end of the cable. No Device (slave) (slave) IDE device CRW8824E (master) (master) Hard Disk Connect. Example-2 IDE cable (primary) IDE cable (Secondary) No device (slave) CD-ROM Drive e. t. c. CRW8824E Remove. (master) 6 Remove the four screws holding the CD-ROM drive in place, then slide the drive forward and out of the drive bay. Before removing the CD-ROM drive from the computer, make sure that all the cables have been removed from the CD-ROM drive's rear panel. Do not force pulling or apply excessive force to the CD-ROM drive. Replacing Drive 13 Installation 7 Set the CRW8824E as master. Plug the included plastic shunt to the MASTER jumper switch on the rear panel of the CRW8824E. Rear Panel AUDI O OUT RG L CSE L SLAV E MAST ER 1 IDE INTE CON RFACE NEC TOR DC IN PU T +5V G+ 12V RGL CSEL SLAVE MASTER Plastic shunt Set to MASTER. Jumper switches The plastic shunts actually contain metal for bridging the two pins of a jumper switch, creating an electrical connection between them when attached. When removed, the jumper switch is set to "OFF. " Store unused plastic shunts in a safe place where they will not be lost. Use a pair of long-nosed pliers to attach or detach the plastic shunts accordingly. [. . . ] 8 Session-at-Once (SAO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SLAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 12 sound card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]