User manual YAMAHA CRW8824SZ

[. . . ] FCC INFORMATION COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW8824S CRW8824S-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] 10 Installation 2 Parity Check The parity check is used for error correction during data transmissions. If paritychecking has to be disabled, the shunt on the Parity jumper switch should be removed. Parity ON (Default) Normally leave this setting alone. ID SELECT PARITY TERMINATOR BLOCK SIZE ID SELECT PARITY TERMINATOR BLOCK SIZE Parity OFF 1 24 1 24 By factory default, the Parity switch is set to "ON" and should normally be left in this state. 3 Termination Terminators prevent SCSI signals from being reflected off the last device in the chain. The SCSI terminator switch should be set to "ON" if the CRW8824S is the last device on the internal SCSI chain. If the CRW8824S is not the last device on the internal SCSI chain, the shunt on the Terminator jumper switch should be removed. Computer Hard disk drive (unterminated) CRW8824S (terminated) MO drive (terminated) SCSI adapter card Terminator By factory default, the Terminator switch is set to "ON. " 11 Installation Termination ON (Default) ID SELECT PARITY TERMINATOR BLOCK SIZE Termination OFF ID SELECT PARITY TERMINATOR BLOCK SIZE 1 24 1 24 Set to "ON" if CRW8824S drive is last device on SCSI chain 4 Block Size The data block size of the CRW8824S can be set to 512 bytes per sector by setting the Block Size jumper switch to "ON. " This is necessary when installing the CRW8824S on a UNIX-based workstation. It is not necessary for Windows 95/98/ 98SE/NT4. 0/2000 computers. Block size OFF (Default) ID SELECT PARITY TERMINATOR BLOCK SIZE Block size ON ID SELECT PARITY TERMINATOR BLOCK SIZE 1 24 1 24 Set to "ON" when installing CRW8824S drive on UNIX workstation By factory default, the Block Size jumper switch is set to "OFF" and should normally be left in this state. 12 Installation Installing the CRW8824S Drive You can install the CRW8824S drive in one of two possible ways: As an additional drive If the casing of your computer has a spare 5. 25-inch drive bay available, such as with many tower-type designs, you can fit the CRW8824S drive in addition to the computer's existing CD-ROM drive. CRW8824S As a replacement drive If the casing of your computer does not have a spare 5. 25-inch drive bay available, such as with many desktop-type designs, you can replace the computer's existing CD-ROM drive with the CRW8824S drive. CD-ROM drive CRW8824S When replacing an IDE-type CD-ROM drive with the CRW8824S drive, you will also need a SCSI adapter card and an internal SCSI flat cable. 13 Installation Fitting the CRW8824S as an Additional Drive 1 Power down your computer and unplug it from the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CRW8824S drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don't lose them. The method for removing the casing and fitting the drive in the drive bay can vary depending on the manufacturer. Refer to the documentation that came with your computer for further details. 14 Installation 3 Touch a metal part of the computer's chassis or power supply unit to drain any static charge that may have built up inside your body. Drain any static charge You can permanently damage equipment if you touch it while there is any static charge in your body. 4 Remove the front cover of a vacant 5. 25-inch drive bay slot in the computer and slide the drive backwards into the slot. Do not apply excessive force when sliding the drive back into the drive bay slot. 15 Installation 5 Leave enough room behind the drive for connecting the power, SCSI and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place. About SCSI adapter card termination To connect internally-mounted SCSI devices, the SCSI adapter card's on-board internal SCSI termination must be switched ON. With most cards, this is done automatically. If your SCSI adapter card requires that you manually disable internal termination, refer to the documentation that came with it. 16 Installation 6 Connect one end of the 50-pin SCSI flat cable to the computer's SCSI adapter card. Align the red line of the cable with Pin 1 of the card's SCSI connector. Next, connect a free 50-pin connector on the SCSI flat cable to the back of the CRW8824S drive such that the red line on the cable is aligned with pin 1, marked "SCSI INTERFACE CONNECTOR 1. " 50-pin SCSI flat cable Align red line with Pin 1 of SCSI INTERFACE CONNECTOR 1 SCSI adapter card Mark Pin 1 AUDIO OUT RG L1 24 ID SE LE PARIT CT TERM Y BLOC INATOR K SIZ E 1 SCSI INTER CONN FACE ECTO R DC INP UT +5 V G +1 2V To Pin 1 1 SCSI INTERFACE CONNECTOR Pin 1 Align red line with Pin 1 of SCSI INTERFACE CONNECTOR 1 17 Installation 7 Connect the audio cable between the CRW8824S drive and the computer's sound card, or the motherboard's audio connector if it has built-in audio. One end of the audio cable has two connectors: a vertically-mounted type (PH) and a horizontally-mounted type (MPC). Choose one that matches your sound card's connector. The connector at other end of the cable is connected to "AUDIO OUT" of the CRW8824S drive. Make sure connector's lug is at the top. Lug AUDI O OU T RG L1 24 ID SE PARI LECT TY TERM BLO IN ATOR CK SI ZE 1 SCSI INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V Audio cable Horizontally-mounted type (MPC) Sound card Vertically-mounted type (PH) You do not need to connect the audio cable to write audio CDs since the audio is passed over the SCSI bus. It is required for playing back audio CDs on the CRW8824S drive via the computer's sound card. However, if a CD-ROM drive is already connected to the sound card, you should use this drive to play back your audio CDs. To listen to audio CDs without a computer sound card, connect headphones or speakers to the headphone jack on the CRW8824S drive's front panel. 18 Installation 8 Connect a 4-pin power cable to the power supply connector of the CRW8824S marked "DC INPUT. " AUDI O OU T RG L1 24 ID SE PARI LECT TY TERM BLOC IN ATOR K SIZ E 1 SCSI INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V Top 4-pin power cable Bottom There may be more than one 4-pin power cable available. These connectors are D-shaped so it is only possible to connect the power cables the correct way round. [. . . ] 36 shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 sound card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 26 static charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 23 F firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]