User manual YAMAHA CS1D

[. . . ] Owner's Manual FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] 3 OUTPUT [TO ST] switch and LED When a MIX channel is selected, this is an on/off switch for the signal sent from that MIX channel to the STEREO bus. (When on, the LED will light. ) This is linked to the MIX [TO ST] switch of the MIX OUTPUT block. This switch is valid only if a MIX channel is selected in the SELECTED OUTPUT CHANNEL block. 4 OUTPUT [TO MTRX] switch and LED When the STEREO A, B channel or a MIX channel 1­48 is selected, this is an on/off switch for the signal sent from that channel to the MATRIX bus. (When on, the LED will light. ) When this switch is off, no signal can be sent from that channel to any MATRIX bus. This is linked with the MIX OUTPUT block MIX [TO MTRX] switch and the STEREO OUTPUT block STEREO A [TO MTRX] switch. The send level settings can be made in the display. This switch is valid only when the STEREO A, B channel or a MIX channel is selected in the SELECTED OUTPUT CHANNEL block. 5 OUTPUT [PAN/BAL] encoder and LEDs This encoder adjusts the pan or balance, according to the group or pair on/off status of the currently selected output channel. The approximate current setting is shown by the perimeter LEDs. 63 CS1D Reference Manual (Hardware) (A)When the OUTPUT [TO ST PAN]/[BAL] LEDs are dark The OUTPUT [PAN/BAL] encoder will have no effect. This will be the state when an unpaired MATRIX channel is selected in the SELECTED OUTPUT CHANNEL block. (B) When the OUTPUT [TO ST PAN] LED is lit The OUTPUT [PAN/BAL] encoder will adjust the pan of the signal sent from the MIX channel to the STEREO bus. This will be the state when a MIX channel is selected in the SELECTED OUTPUT CHANNEL block for that MIX channel. (C)When the OUTPUT [BAL] LED is lit The OUTPUT [PAN/BAL] encoder will adjust the volume balance of the paired output channels (or of the L/R channels of STEREO A/B). This will be the state when a paired MIX/MATRIX channel or the STEREO A/B channel is selected in the SELECTED OUTPUT CHANNEL block. Normally, the OUTPUT [TO ST PAN]/[BAL] switch LED will automatically be lit or dark depending on the type or pair on/off status of the currently selected output channel. However, only if a paired MIX channel is selected and the OUTPUT [TO ST] switch (3) is turned on for those MIX channels, the OUTPUT [PAN/BAL] encoder can be used for either of the above-listed functions (B) and (C). In this case, you yourself will need to press the [TO ST PAN] switch or [BAL] switch to specify the function controlled by the encoder. When the [TO ST PAN] switch LED is lit, you can use the OUTPUT [PAN/BAL] encoder to adjust the pan of the signal that is sent from the MIX channel to the STEREO bus. (The section enclosed by dashed lines in the following diagram corresponds to the [PAN/BAL] encoder. ) OUTPUT LEVEL PAN MIX 1 ON PAN MIX 2 Also, when the [BAL] switch LED is lit, you can use the OUTPUT [PAN/BAL] encoder to adjust the volume balance of paired MIX channels. (The section enclosed by dashed lines in the following diagram corresponds to the [PAN/BAL] encoder. ) · Adjusting the volume balance of paired MIX channels OUTPUT LEVEL MIX 1 ON OUTPUT PATCH BAL MIX 2 7 OUTPUT [LEVEL] encoder and LEDs This sets the output level of the currently selected channel. The range is ­ dB ­ +10 dB (1 dB steps), and the approximate current value is shown by the perimeter LEDs. 8 OUTPUT [CUE] switch and LED This switch monitors the currently selected MIX channel. [. . . ] 1 2 3 4 5 6 7 8 9 10 11 12 13 Signal Data OUT 1 Data OUT 3 Data OUT 5 Data OUT 7 GND GND GND GND +5V Data IN 2 Data IN 4 Data IN 6 Data IN 8 Pin No. 14 15 16 17 18 19 20 21 22 23 24 25 Signal Data OUT 2 Data OUT 4 Data OUT 6 Data OUT 8 GND GND GND +5V Data IN 1 Data IN 3 Data IN 5 Data IN 7 77 Appendices Accessories DIGITAL AUDIO CABLE CONTROL CABLE LAMP DUST COVER OWNER'S MANUAL PM1D SYSTEM SOFTWARE DISC (CD-R media) 10m × 1 10m × 2 ×4 ×1 ×1 ×1 Dimensions 1906 355 Unit: mm Specifications and external appearance subject to change without notice. For European Model Purchaser/User Information specified in EN55103-1 and EN55103-2. Conformed Environment: E1, E2, E3 and E4 78 974 Cards Specifications Cards Specifications · LMY2-ML 1. [. . . ]