User manual YAMAHA CVP-205-CVP-205M-CVP-203

[. . . ] CVP-205/205M/203 OWNER'S MANUAL OWNER'S MANUAL SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. Battery Notice: This product MAY contain a small non- rechargable battery which (if applicable) is soldered in place. [. . . ] The operations here apply to step 6 on page 98. 1 1-1 1-2 While holding down this note. . . Select this note. 1-3 . . . press this (to input a tie). The notation display on the instrument (CVP-205) may not be accurate, especially for tied notes or longer notes. To have the notation displayed accurately, set the gate time to tenuto by using the [H] button, and input the notes as desired. 2 2-2 2-3 2-4 2-1 Select this note. 3 3-1 Press this button to display the dotted notes. 3-3 3-2 Select this note. 4 4-1 4-3 Call up the normal notes by pressing this button. 4-2 Select this note. To input rests, simply move the measure/beat/clock location for the desired rest time, then input the next note. I Play back the newly created melody Use the [C] ( L ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. The entered data can be edited from the SONG CREATOR (1 - 16) display (page 106). CVP-205/203 99 Recording Your Performances and Creating Songs-- Song Creator Recording Chord Changes for the Auto Accompaniment -- Step Record (Chord) The Chord Step recording feature makes it possible to record auto accompaniment chord changes one at a time with precise timing. Since the changes don't have to be played in real time, you can easily create complex, tight chord changes -- over which you can record the melody in normal fashion. The operations here apply to step 6 on page 98. Entering Chords and Sections (Chord Step) For example, you can input the following chord progression by the procedure described below. MAIN A BREAK MAIN B C F G F G7 C Enter the chords by using the currently selected chord fingering method in the Auto Accompaniment section of the keyboard. 1 Press the MAIN [A] button to specify the section, and enter the chords as shown at right. MAIN A MAIN C F G C 001:1:000 F 001:3:000 Select this note value and play the chords indicated at right. G 002:1:000 2 Press the [BREAK] button to specify the Break section, and enter the chords as shown at right. MAIN A BREAK C F G F G7 F BREAK INTRO 002:3:000 G7 002:4:000 Select this note value and play the chords indicated at right. 100 CVP-205/203 Recording Your Performances and Creating Songs-- Song Creator 3 Press the MAIN [B] button to specify the section and enter the chord indicated at right. MAIN A BREAK MAIN B MAIN C F G F G7 C C 003:1:000 Select this note value and play the chords indicated at right. I Play back the newly created chord progression Use the [C] ( L ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. The entered data can be edited from the SONG CREATOR (CHD) display (page 107). Finally, press the [F] (EXPAND) button from the SONG CREATOR (CHD) display in order to convert the input data into song data. To enter a fill-in, press the [AUTO FILL IN] button and press one of the MAIN [A] ­ [D] buttons. END Mark An "END" mark is shown in the display, indicating the end of the song data. The actual position of the End mark differs depending on the section that is input at the end of the song. When an Ending section is input, the End mark automatically follows the Ending data. When a section other than Ending is input, the End mark is set two measures after the final section. The End mark can be freely set to any position desired. CVP-205/203 101 Recording Your Performances and Creating Songs-- Song Creator Select the Recording Options: Starting, Stopping, Punching In/Out -- Rec Mode From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording. To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation steps 1 - 3 on page 97. These settings determine how recording will start. Normal Pressing the SONG [START/STOP] button enables Synchro standby and overwrite recording starts as soon as you start playing the keyboard. First Key On Overwrite recording starts as soon as you start playing the keyboard. This setting also preserves the previous lead-in data, letting you record over the original lead-in without erasing it. Punch In At The song plays back normally up to the indicated Punch In measure (set by the [3LM] buttons), then starts overwrite recording at that Punch In measure. Determines the measure at which Punch In overwrite recording starts (when "PUNCH IN AT" is selected). These settings determine how recording will stop as well as what happens to previously recorded data. Replace All This deletes all data following the point at which recording is stopped. Calls up the SONG display, from which you can save the edited data. When this is set to ON, you can use the sostenuto (center) pedal to control the punch-in and punch-out points. [. . . ] Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 SWEDEN Yamaha Scandinavia AB J. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 BRAZIL Yamaha Musical do Brasil LTDA. Rebouças 2636, São Paulo, Brasil Tel: 011-853-1377 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 ARGENTINA Yamaha de Panamá S. A. [. . . ]