User manual YAMAHA CVP-309-CVP-307-CVP-305-CVP-303-CVP-301 DATA LIST

[. . . ] To change the setting use a "minus" screwdriver to rotate the selector dial so that the correct voltage appears next to the pointer on the panel. WICHTIG Netzspannung überprüfen Vergewissern Sie sich vor dem Anschließen an das Stromnetz, daß die örtliche Netzspannung den Betriebsspannungswerten auf dem Typenschild an der Unterseite des Instruments entspricht. In bestimmten Verkaufsgebieten ist das Instrument mit einem Spannungswähler an der Unterseite neben der Netzkabeldurchführung ausgestattet. Falls vorhanden, muß der Spannungswähler auf die örtliche Netzspannung eingestellt werden. Der Spannungswähler wurde werkseitig auf 240 V voreingestellt. [. . . ] If you do this after making any edits that you have not yet written, the "Write edited data?" confirmation prompt will appear. Press YES to write the edited data and then exit from the Initial Edit mode, NO to exit without writing the data, or CANCEL to return to the Initial Edit mode. Renaming Song Files This function lets you enter an original name for, or change the existing name of, any song file on the disk recorded by the CVP-79A/69/69A/59S. The rename function is accessed via the RECORD [RENAME] display (RECORD display page 7). ZSelect a Song & Engage the Rename Mode . . . . . . . . . . . . . . . . . . . . . . . . Use the SONG v and w buttons, the data dial, or the [+]/[­] buttons to specify the song you want to rename, then press the RENAME LCD button to go to the NAMING display. 87 XEnter a Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The current song file name appears in the upper right corner of the display. Use the > LCD button to position the underline cursor at the character you want to change (song names can be up to 12 characters in length). Use the data dial or [+]/[­] buttons to select the character you want to enter from the list in the center of the display, then press the c. set LCD button to enter the character at the current cursor position. Repeat this procedure until your name is complete. The c. del LCD button can be used to back up one space and delete a character. CRegister the Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When the name is complete press the OK LCD button to register the name for the current song file, or CANCEL to abort. Press the [EXIT] button, or the [RECORD] button so that its indicator goes out, to exit from the Rename mode. 88 Song Recording Song Recording Recording Without a Disk The Clavinova has enough internal RAM memory (about 25KB) to allow recording for a while even if a disk is not loaded (up to approximately 2, 500 notes if no other data is recorded). · Chord sequence data is not recorded to internal RAM memory. -- The "Button not valid !" alert display will appear. · The Punch-in/out Recording, Track Mix, Track Delete, Track Quantize, Initial Edit, and Rename functions (i. e. RECORD display page 3 to the last page) cannot be used with data in the internal RAM memory. Use the TUNE v and w LCD buttons to set the tuning as required. The data dial and [+]/[­] buttons can also be used once the TUNE parameter has been selected. The default value of 440. 0Hz can be instantly recalled by pressing the TUNE v and w LCD buttons simultaneously. · The Tune setting is retained in memory even when the power is turned off if the BACKUP page TUNE/MICRO TUNING parameter is turned on (page 107), otherwise the tuning is always set at 440. 0Hz when the power is turned on. · The Tune function does not affect the Drum Kit voices. s Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The pan positions of the left-hand voice in a split keyboard setup (LEFT), the 2nd voice in the dual mode (2ND), and the right-hand or main voice (RIGHT/1) can be individually set via the appropriate PAN parameters. Press the LEFT, 2ND, or RIGHT/1 LCD button according to the voice you want to pan, then use the data dial or [+]/[­] buttons to set the pan position as required. The graphic bar shows the approximate pan position between full left ("L") and full right ("R"). The default position can be instantly recalled by pressing the [+] and [­] buttons simultaneously. Pedal CVP-79A 92 · The pan setting is retained in memory even when the power is turned off if the BACKUP page VOICE SETTING parameter is turned on (page 107). · The default pan position for some voices is center, while some voices feature keyboard scaling -- i. e. the keyboard is spread across the stereo sound field (see the voice list on page 116). Both types appear in center position on the LCD. Any changes in the pan setting are then relative to the default position. [. . . ] The required supply voltage is printed on the name plate. For name plate location, please refer to the graphic found in the Special Message Section of this manual. 2. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by the manufacturer. If a cart, rack, or stand is used, please observe all safety markings and instructions that accompany the accessory product. 9. The power supply cord (plug) should be disconnected from the outlet when electronic products are to be left unused for extended periods of time. Cords should also be disconnected when there is a high probability of lightening and/or electrical storm activity. 10. This product may be equipped with a polarized plug (one blade wider than the other). [. . . ]