User manual YAMAHA CVP-20

[. . . ] The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. Warning: Do not attempt to recharge, disassemble, or CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. incinerate this type of battery. Dispose of used batteries promptly and as regulated by applicable laws. [. . . ] Finally, press the [F] (EXPAND) button from the SONG CREATOR (CHD) display in order to convert the input data into song data. To enter a fill-in, press the [AUTO FILL IN] button and press one of the MAIN [A] ­ [D] buttons. END Mark An "END" mark is shown in the display, indicating the end of the song data. The actual position of the End mark differs depending on the section that is input at the end of the song. When an Ending section is input, the End mark automatically follows the Ending data. When a section other than Ending is input, the End mark is set two measures after the final section. The End mark can be freely set to any position desired. 102 CVP-209/207 Recording Your Performances and Creating Songs-- Song Creator Select the Recording Options: Starting, Stopping, Punching In/Out -- Rec Mode From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording. To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation steps 1­3 on page 98. These settings determine how recording will start. Normal Pressing the SONG [START/STOP] button enables Synchro standby and overwrite recording starts as soon as you start playing the keyboard. First Key On Overwrite recording starts as soon as you start playing the keyboard. This setting also preserves the previous lead-in data, letting you record over the original lead-in without erasing it. Punch In At The song plays back normally up to the indicated Punch In measure (set by the [3LM] buttons), then starts overwrite recording at that Punch In measure. Determines the measure at which Punch In overwrite recording starts (when "PUNCH IN AT" is selected). F G H I Calls up the SONG display, from which you can save the edited data. The Undo function only has one level; only the previous operation can be undone. D I E J Calls up the SONG display, from which you can save the edited data. 1 2 3 4 5 6 7 8 These select the channel to be deleted. Mix This function lets you mix the data of two channels and place the results in a different channel. It also lets you copy the data from one channel to another. Use these to select the desired edit operation. A F All data other than the mixed note data is derived from the Source 1 channel. B G C H Executes the Mix operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you're not satisfied with the Mix results. The Undo function only has one level; only the previous operation can be undone. D I E J Calls up the SONG display, from which you can save the edited data. 1 2 3 4 5 6 7 8 These let you specify the two source channels to be mixed. Determines the channel into which the mix or copy results will be placed. If "COPY" is selected here, the data from Source 1 is copied to the Destination channel. CVP-209/207 105 Recording Your Performances and Creating Songs-- Song Creator Channel Transpose This allows you to transpose the recorded data of individual channels up or down by a maximum of two octaves in semitone increments. Toggles between the two channel displays: Channels 1 - 8, and Channels 9 - 16. To simultaneously set all channels to the same value, adjust the Channel Transpose for one of the channels while holding down this button. A F Use these to select the desired edit operation. B G C H Executes the Channel Transpose operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you're not satisfied with the Channel Transpose results. The Undo function only has one level; only the previous operation can be undone. D I E J Calls up the SONG display, from which you can save the edited data. 1 2 3 4 5 6 7 8 Determines the amount of transpose for each channel. Set Up You can change the initial settings of the song -- such as voice, level, and tempo -- to the current settings of the mixing console or panel controls. Use these to select the desired edit operation. A F B G C H Executes the SET UP operation. Once SET UP has been executed, the operation cannot be cancelled or undone. D I E J Calls up the SONG display, from which you can save the edited data. 1 2 3 4 5 6 7 8 Use this to checkmark the selected item. Checkmarked items are stored with the song. Determines which playback features and functions will be automatically called up along with the selected song. All events, with the exception of "KEYBOARD VOICE, " can be recorded only at the beginning of the song. Before you select or checkmark any of these items (other than Keyboard Voice), make sure to return the song to the beginning by using the [TOP] button, and stop playback. [. . . ] De C. V. , Departamento de ventas Javier Rojo Gomez No. 1149, Col. Tel: 686-00-33 KOREA Yamaha Music Korea Ltd. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0661 GREECE Philippe Nakas S. A. Navarinou Street 13, P. Code 10680, Athens, Greece Tel: 01-364-7111 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. [. . . ]