User manual YAMAHA CVS10E

[. . . ] 9 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 About Connections . . . . . . . . . . . . . . . . . . . . . . . . 13 Daisy Chain Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Star Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 About Dante Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The +48V indicators also function as error indicators: the indicators for all channels will flash if an error occurs. CAUTION: · Make sure that phantom power is turned OFF unless it is needed. · When turning phantom power ON, make sure that no equipment other than phantom-powered devices such as condenser microphones are connected to the corresponding [INPUT] connectors. Applying phantom power to a device that does not require phantom power can damage the connected device. · Do not connect or disconnect a device to an INPUT while phantom power is applied. Doing so can damage the connected device and/or the unit itself. F 012 B C · To prevent possible damage to speakers, make sure that power amplifiers and/or powered speakers are turned OFF when switching phantom power ON or OFF. We also recommend setting all digital mixing console output controls to minimum when turning phantom power ON or OFF. Sudden high level peaks caused by the switching operation can damage equipment as well as the hearing of those present. 3 [SIG] (Signal) Indicators These indicators light green when the signal applied to the corresponding channel reaches or exceeds ­34 dBFS. The SIG indicators also function as error indicators: the indicators for all channels will flash if an error occurs. 4 [PEAK] Indicators These indicators light red when the signal level of the corresponding channel reaches or exceeds ­3 dBFS. The PEAK indicators also function as error indicators: the indicators for all channels will flash if an error occurs. 5 [UNIT ID] Rotary Switch This rotary switch enables you to set an ID number so that connected devices will recognize the Rio. The UNIT ID must be a unique number in the network so that the Rio will be able to transmit and receive audio signals over a Dante network, or be controlled from a connected digital mixing console. Use the rotary switch while the power to the unit is turned OFF. If the green indicator lights, the unit is operating as a word clock slave and synching to the word clock. If the green indicator flashes, the unit is operating as the word clock master. If the power to the unit is turned on but the green indicator is turned off, the unit is not functioning properly. In this case, refer to the "Messages" section (see page 17). If the orange indicator lights or flashes, refer to the "Messages" section. 9 [+48V MASTER] Switch This is the master switch for the unit's +48V phantom power supply. If the [+48V MASTER] switch is off, no phantom power will be supplied to the unit's input connectors even if the individual input phantom power settings are ON. However, the [+48V] indicators will light on channels for which phantom power is turned ON even if the [+48V MASTER] switch is OFF. 0 Power Indicator Lights when AC power to the unit is ON. A Power Switch ( CAUTIONS: ) Turns power to the unit ON or OFF. · Rapidly turning the unit on and off in succession can cause it to malfunction. After turning the unit off, wait for about 6 seconds before turning it on again. · Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. B AES/EBU OUT Connectors 1/2­7/8 (Rio3224-D only) These XLR-3-32 type balanced connectors deliver AES/EBU format digital output from the unit's corresponding output channels. Each connector outputs 2-channel digital audio. C OUTPUT +4 dBu Connectors 1­16 {1­8} These XLR-3-32 type balanced connectors deliver analog output from the unit's corresponding output channels. [. . . ] (1= GND, 2= HOT, 3= COLD) Owner's Manual 19 Specifications Dimensions (5. 7) 480 5. 8 220 (5. 7) 480 5. 8 132 12 144 361. 5 12 232 361. 5 Rio3224-D Rio1608-D 350 350 Unit: mm * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. 20 Owner's Manual Specifications MEMO Owner's Manual 21 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]