User manual YAMAHA CX-1000

[. . . ] 11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 16 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the rear of the unit. [. . . ] TOTAL TUNER R L TAPE 1 TAPE 2 VCR 1 VCR 2 PRE OUT IN OUT IN OUT PHONO GND R R SWITCHED PB REC OUT PB REC OUT PB REC OUT PB REC OUT I20V 60Hz AC OUTLETS AUDIO SIGNAL VIDEO SIGNAL To AC outlet OUTPUT GND AUDIO OUT AUDIO OUT VIDEO OUT VIDEO OUT LINE OUT AUDIO IN Turntable LD player, TV tuner, etc. Tape deck 2 Video cassette recorder 2 VIDEO IN LINE IN Monitor TV * : Refer to "ABOUT THE ACCESSORY COMPONENTS ON THE REAR PANEL" on page 6. VIDEO IN 5 CONNECTING TO S VIDEO TERMINALS <For CX-2 only> If your video cassette recorder, LD player, etc. and your monitor are equipped with "S" (high-resolution) video terminals, connect them to this unit's S video terminals, and connect this unit's S MON OUT terminal to the "S" video input of your monitor. Otherwise, connect the composite video terminals from your video cassette recorder, LD player, etc. to the composite video terminals of this unit, and connect this unit's composite MON OUT terminal to the composite video input of your monitor. Note If video signals are sent to both S video input and composite video input terminals, the signals will be sent to their respective output terminals independently. Video cassette recorder 1 Video cassette recorder 2 Monitor TV S VIDEO OUT VIDEO OUT VIDEO OUT S VIDEO OUT VIDEO IN S VIDEO IN S VIDEO IN VIDEO IN S VIDEO IN VIDEO IN LD Player IN VCR 1 VCR 2 MON OUT VIDEO OUT S VIDEO OUT IN OUT IN OUT S video terminals Composite video terminals VIDEO SIGNAL ABOUT THE ACCESSORY COMPONENTS ON THE REAR PANEL AC OUTLETS (SWITCHED) (U. S. A. , Canada, Europe and General models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SWITCHED OUTLETS (Australia and U. K. models) . . . . . . . . . . . . . . . . . . 1 SWITCHED OUTLET Use these to connect the power cords from your components (except a power amplifier, integrated amplifier and receiver) to this unit. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 200 watts. Strictly be careful not to exceed this value. The power to the SWITCHED outlets is controlled by this unit's POWER switch or the provided remote control transmitter's POWER key. These outlets will supply power to any component whenever this unit is turned on. GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. REMOTE CONTROL (POWER AMP) connector If you have the YAMAHA power amplifier MX-1 or MX-2, connect this connector to the REMOTE CONTROL (PRE AMP) connector of the power amplifier by using the provided cable. By this connection, the power of the power amplifier is controlled by this unit's POWER switch or the provided remote control transmitter's POWER key. On each key function, refer to the corresponding instruction on your component's manual. For Control of This Unit POWER Turns the power on/off. Input selector keys Selects input source. Tuner keys Controls tuner +: Selects higher preset station number. ­: Selects lower preset station number. A/B/C/D/E Selects the page (A ­ E) of preset station buttons. MUTING When pressed, mutes the volume level. To resume original volume level, press this again. While muting, the indicator above the VOLUME control on the front panel illuminates. CD player keys Controls compact disc player. * DISC SKIP is applicable only to compact disc changer. VOLUME +/­ Turns the volume level up/down. LD player keys (U. S. A. , Canada and General models of CX-2 only) Controls LD player. * There are some models which have a key with both the functions of PLAY and PAUSE. Tape deck keys Controls tape deck. * DIR A, B and DECK A/B are applicable only to double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. STANDBY mode (For Europe model only) While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the STANDBY mode. (In this mode, the indicator is half illuminated. ) Note To turn the power off completely, disconnect the AC power plug from the wall outlet. POWER POWER POWER on mode STANDBY mode 13 REMOTE CONTROL "LEARNING" FUNCTION (U. S. A. , Canada and General models of CX-2 only) The keys on this remote control transmitter can be programmed to "learn" key-functions from other remote control transmitters without losing the preset key functions. By using this feature, this unit can then be used in place of one or more other remote control transmitters, thus making operation of your various audio and video components more convenient. [. . . ] total Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435 x 86 x 319 mm (17-1/8" x 3-3/8" x 15-15/16") Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. 4 kg (11 lbs. 14 oz. ) Accessories . . . . . . . . . . . Remote control transmitter Batteries Remote control cable Audio connection cord 17 TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM The unit fails to turn on when the POWER switch is pressed. CAUSE Power cord is not plugged in or is not completely inserted. [. . . ]