User manual YAMAHA D-3

[. . . ] Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Do not attach acoustic drums to the electronic drum rack. [. . . ] Hold the Trigger Module attachment part turn it gradually. Tighten the two knobs loosened and fix the position of the Trigger Module attachment part . K H C F L J D Checking the contents of the Pad Set and the Trigger Module Open the DTP4K2STD (Pad Set) and Trigger Module package and confirm the contents. Figure 7: Pad Set DTP4K2STD TP65 (Drum Pad) (3) TP65S (3-zone Drum Pad) (2) Clamp Bolt (5) Checking the contents of RS70 Open the RS70 (Rack System) package and confirm the contents. Figure 2: RS70 (Rack System) RS70 (1) q w e r t y u i DTXP4 (Drum Trigger Module) TP65S (3-zone Drum Pad) AC Adaptor HH65 (Hi-Hat Controller) PCY135 (3-zone Cymbal Pad) TP65 (Drum Pad) KP65 (Kick Pad) RS70 (Rack System) Cable Band (10) *1 G E TP65S has a grooved rim. Assembly Manual (1) *2 - RS70 PCY135 (Cymbal Pad) (2) 6 7 Felt (Large) (2) See Figure 5. Loosen the two knobs ((f) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((g) on the middle right) aligned at the base of pipe . Move pipe in a counterclockwise direction until it is about 90 degrees from the pipe with the YAMAHA logo. Tighten the two knobs loosened and fix the position of pipe . Loosen the knobs (h) and (j) (shown with on the opposite side of pipe ) of the cymbal and on the right and left and pull up the cymbal holders vertically to the holders height illustrated. Tighten the knobs loosened and fix the positions of the cymbal holders. Hold the upper area of the vertical pipe Be sure to move pipe in a counterclockwise direction. If you move it in a clockwise direction, the slim pipes may collide and bend. and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2 to 5. 9-channel snake cable (1) Instruction Manual (4) - TP65/65S/100/120SD - PCY65/65S/135/155 - HH65 - KP65 Figure 8: Trigger Module DTXP4 (1) Wing Bolt (2) AC Adaptor (1) Module Stand (1) * YAMAHA logo printed on pipe is facing the opposite side. 2 See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left. Continued on the next page (on the back side) Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat. Figure 15: Cymbal holder-2 Figure 16: Cymbal holder-3 Installing the HH65 (Hi-Hat controller) and KP65 (Kick pad) Figure 22: HH65 and KP65 Connecting to a power source Connect the AC adaptor to the DTXP4. Figure 26: Power switch (DTXP4 rear panel) 1 @4 Stopper @5 Drum key @6 Key bolt See Figure 15. Attach the stopper to the cymbal holder, and fix at a position where the L-shaped part of the stopper is on the opposite side from you. To fix the position of the stopper (@4), use the drum key (@5) and tighten the key bolt (@6) firmly. Attach the black plastic part removed in step 1 to the cymbal holder, and tighten it in a clockwise direction. Attach one of the felt washers removed in step 1 to the cymbal holder. [. . . ] For regular assembly, connect the straight plugs to the input jacks in accordance with the indication on each label. Figure 25: Diagram of standard connection Figure 12: Tom Holder and Drum Pad !4 Tom holder !5 Clamp bolt Attach the TP65 (Drum pad) to the tom holder as shown in Figure 12. Tighten the clamp bolt and fix the position. Repeat step 3 and 4 in the same manner for tom holder at the on the right, and attach the TP65 (Drum center of the rack system and for tom holder pad) to each tom holder. Loosen the knobs of the tom holder on the left (shown with ). [. . . ]