User manual YAMAHA D-80

[. . . ] · Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Mounting the Pads and the Drum Trigger Module on the Rack System Mount the Pads and the Trigger Module on the Rack System. Then position the Kick Pad and the Hi-Hat. Attaching the Cymbal Holder Attaching the Tom Pad WARNING 1. Remove the cap of the rack by loosening the screw on the top of the vertical support. 2. [. . . ] Loose bolts may result in the rack overturning or parts dropping, causing injury. · Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting up the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. Doing so may result in injury or damage/deterioration to the product. · Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. 2. Attach the Cymbal Holders (CH750 x 2 and CH755 x 1) to the Rack System as shown below. rack respectively. As shown below, attach the Tom Pad to the rod part so that the rod part is to be inserted to the hole of the Tom Pad, then tighten the clamp bolt firmly. Tom pad Rod parts Clamp rod CH750 CH750 XP120T Clamp bolt To be inserted NOTICE · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Turn the wing nut until you are certain that the Cymbal Pad is attached. The Cymbal Pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Felt washer supplied with the Cymbal Pad Wing nut Basket Pad Beater Adjustment knob Legs Foot pedal (sold separately) Key bolt XP120SD (Snare Pad) 3. Attach the tilter sleeve removed in step 1 to the 1. Remove the wing nut and the two felt washers from the Cymbal Holder. Then turn the tilter sleeve in a counterclockwise direction and remove it. Wing nut Felt washer Felt washer Tilter sleeve Cymbal holder Tilter sleeve Cymbal Holder again, and tighten it in a clockwise direction. a 4. Attach one of the felt washers removed in step 1 to the Cymbal Holder. The other felt washer will not be used within the standard assembly described in this manual. 4 5 Locate the Hi-Hat Stand, Kick Pad and Snare Stand as desired, referring to "Unit Standard Assembly" on the front page. NOTICE Before assembling the unit, lay a drum mat (sold separately) on the floor. If a drum mat is not available, lay the cardboard of the included package under the Hi-Hat Stand and Kick Pad to prevent damaging the floor. Connecting the pads to the Drum Trigger Module Connect the cables plugged into the Output jacks of the Pads to the Input jacks of the Drum Trigger module. Jacks of the Pads y u i t r q Attaching the Drum Trigger Module 1. Attach the included module stand to the back side of the Drum Trigger Module by using the module stand fastening screws. 2. Attach the module stand onto the holder clamp, then tighten the knob to fix the position. SNARE ­ !0 KICK/!1 and HI-HAT CONTROL jack) of the Drum Trigger Module by using the stereo phone cables. · Insert the straight plugs of the cable into the Trigger Input jacks of the Drum Trigger Module, then insert the L-shaped plugs of the cables into each corresponding Pad. 1. [. . . ] Make sure the F (Standby/On) switch is set to the Standby position (?), then connect the AC power adaptor to the DC IN jack on the rear panel. Twist the cable around the cable clip to prevent the DC plug from inadvertently being disconnected. 3. Spread out the legs of the tripod part until it stands stable. Tighten the wing bolt loosened in step 2. 6. [. . . ]