User manual YAMAHA D5000

[. . . ] PROFESSIONAL DIGITAL DELAY OPERATING MANUAL MANUEL D'UTILISATION BEDIENUNGSHANDBUCH DATA ENTRY INPUT LEVEL 0 MIX L CLIP -6 -12 -18 -24 -30 -36 -42 R PROFESSIONAL DIGITAL DELAY CURSOR PARAMETER POWER DELAY FB MOD DUCK PROGRAM STORE RECALL PROGRAM TRIGGER UTILITY BYPASS ON OFF -00 L R +10 DRY WET YDG2030 FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] DUCK means the signal passes until the input level is above the threshold (or when a MIDI Note Off message is received). GATE means the signal passes after the input level is above the threshold (or when a MIDI Note On message is received). Select the source for the trigger signal. When you select one of the IN or OUT settings, the duck or gate is effective depending on the signal level. When TRIG. KEY is set, the [TRIGGER] key or a footswitch connected to the TRIGGER Footswitch Jack on the back panel is used to trigger the duck or gate. If MIDInote is selected, a MIDI Note Off/On message is used as the trigger signal. Select the target direction. SOURCE (IN(L)/IN(R)/ IN(L+R)/OUT(L)/OUT(R)/ OUT(L+R)/TRIG. KEY/ MIDInote) TARGET (IN(L)/IN(R)/ IN(L&R)/OUT(L)/OUT(R)/ OUT(L&R)) HOLD (2 ~ 21000 ms) RELEASE (2 ~ 21000 ms) THRESHOLD (0 ~ 100%) Set the hold time in milliseconds. Select the duck or gate threshold level. Duck/gate The duck/gate can be opened by various triggers. Usually the strength of the input signal is used as the trigger. If TYPE is set to GATE, when the input signal is higher than a certain level (threshold), the GATE opens and the signal can pass. As soon as the input signal drops below the threshold, the GATE closes and the signal is cut. If TYPE is set to DUCK, the signal is cut while the input signal is higher than the threshold. As soon as the signal drops below the threshold, the DUCK is opened and the signal can pass. The threshold is set by the THRESHOLD parameter. Hold and release A short input signal, like the one shown below, would cause the GATE to open (or close in the case D5000 Parameter Edit Mode - 15 of a DUCK) for a very short time. This can sound unnatural, especially if the GATE closes abruptly. There are two parameters which you can adjust, HOLD and RELEASE. By setting a long HOLD time, the gate can be kept open even after the signal has dropped below the threshold. The RELEASE parameter specifies the length of time it takes for the gate to close, causing the signal to gradually cut off. Input Signal Delay Output (TYPE set to GATE) Threshold Hold Release Other triggers The signal level is not the only way to trigger a duck/gate. The [TRIGGER] key or a footswitch connected to the TRIGGER Footswitch Jack on the back panel, or a MIDI Note On (for GATE) or Note Off (for DUCK) message can also be used. The HOLD and RELEASE parameters work with any trigger. Re-trigger If the DUCK/GATE is continuously triggered by any of the other sources, it may be kept from closing. As the GATE responds to a trigger source and will open for the set HOLD time, a trigger received while the GATE is open will act as a "re-trigger", causing the GATE to remain open. D5000 16 - Parameter Edit Mode Editing a sampling/playback program To edit a sampling/playback program, press the [ DELAY ] key. FREEZE program The FREEZE program allows you to sample (digitally record) and playback sounds. [. . . ] When a message is received, the value of the assigned effect parameter is changed according to the control value. Status Control Number Control Value 1011nnnn 0ccccccc 0vvvvvvv (BnH) n = 0 (channel number1) ~ 15 (channel number 16) c = 1 ~ 95 v = 0 ~ 127 4 Program Change Received on the currently set MIDI channel. When a message is received, the corresponding program is recalled from the program change table of the current bank. Status Program Number 1100nnnn 0ppppppp (CnH) n = 0 (channel number1) ~ 15 (channel number 16) p = 0 ~ 127 2) System Exclusive Messages 1 Program Bulk Data Request Received on the currently set MIDI channel. [. . . ]