User manual YAMAHA DM1000V2 1

[. . . ] Owner's Manual Keep This Manual For Future Reference. E FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. [. . . ] Make sure that the [SEL] button indicators for all channels are lit green. The REC and PLAY buttons are highlighted and event recording is armed. However, no events are yet recorded since no channels are selected. 16 Automix DM1000 Version 2--Owner's Manual 198 Chapter 16--Automix 5 Perform the following operations to punch in and out individual events. Parameters Channel Input Bus Out, Aux Send Stereo Out Group Master Fader Pan Input PAN FADER OVERWRITE Operation Set Layer to Iinput, Fader mode to Fader Set Layer to Master, Fader mode to fader Stereo Out fader Set Fader mode to fader. Set Group Master in User Assignable Layer. Set Layer to Input, Encoder mode to Pan Select Input Layer and assign Surround LFE Level or Surround Pan Wheel to the Encoders Use SELECTED CHANNEL EQUALIZER section. (If EQ parameter assigned to an Encoder, also use Encoders. ) Set Layer to Input, Fader mode to Aux Set Layer to Input, Encoder mode to Aux Select internal effects processors Select User Defined Remote Layer Select User Defined Remote Layer Press Encoder and adjust Press Encoder and adjust Adjust SELECTED CHANNEL control3 Press Encoder and adjust Press Encoder and adjust4 Touch fader knob and adjust1 Press Encoder and adjust Move the cursor to the parameter control on the page, then press [ENTER]. Touch fader knob and adjust1 Press Encoder and adjust Press Encoder Punch In Punch Out Channel Levels (faders) Touch fader knob and adjust1 Release fader knob2 Surround Pan Input SURR Press Encoder EQ (F, Q, G) All channels EQ On/Off EQ Press [SEL] button Press Encoder Release fader knob2 Press Encoder Move the cursor to the parameter control on the page, then press [ENTER]. Release fader knob2 Press Encoder Aux Sends 1­8 Level Input AUX Effects parameters (certain parameters) Effects processors 1­4 Faders Encoders -- User Defined Remote Layer 1. 4. FADER PAN To punch in events by performing this operation, set TOUCH SENSE to TOUCH or LATCH on the Fader1 or 2 page. To punch out events by performing this operation, set TOUCH SENSE to TOUCH on the Fader1 or 2 page. To punch in events by performing this operation, turn on the Auto EQ Edit preference. To punch in events by performing this operation, assign EQ parameters to the Encoders. 6 Stop the Automix. A confirmation window regarding updating the Automix data appears. DM1000 Version 2--Owner's Manual [SEL] Button Functions While the [AUTO] Button Indicator Is On 199 [SEL] Button Functions While the [AUTO] Button Indicator Is On While the [AUTO] button indicator is lit, you can use the channel [SEL] buttons to turn the Automix function on and off, arm or disarm channels, or punch channels in and out. The [SEL] button indicators operate as follows: · Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automix recording or playback disabled. · Green . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automix stopped or playing · Orange. . . . . . . . . . . . . . . . . . . . . . . . . . . The channel is armed. · Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automix recording in progress · Flashing red . . . . . . . . . . . . . . . . . . Edit Out mode set to TAKEOVER, and fader events continue recording after punch out · Flashing green. . . . . . . . . . . . . . Edit Out mode set to TAKEOVER, and faders are disabled after punch out Playing Back an Automix As long as the Automix function is enabled, the Automix function will chase the incoming timecode and play and stop the current Automix accordingly. You can stop playback manually by moving the cursor to the STOP or ABORT button on the Automix | Main/Memory page, then pressing [ENTER]. Playback will stop automatically if the DM1000 receives no timecode for a while, if the DM1000 receives MIDI Stop commands (only when the MIDI CLOCK source is selected), or if the end of the Automix data is reached. While the [AUTO] button indicator is lit, the [SEL] button indicators light up green on the channel strips available for Automix playback. When Automix playback for an individual channel is disabled, its [SEL] button indicator turns off. During playback, faders move in accordance with recorded fader events (as long as the corresponding layer and Fader mode is selected). You can disable fader movement by turning off the MOTOR button on the Fader 1 or 2 page (see page 205). [. . . ] 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Central Europe GmbH Sp. z. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. Tel: 714-522-9011 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 INDONESIA PT. [. . . ]