User manual YAMAHA DME-N NETWORK DRIVER INSTALLATION GUIDE FOR M7CL/LS9/DSP5D

[. . . ] Do not attempt to play the disk on an audio CD player. Doing so may result in irreparable damage to your audio CD player. · Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. · Windows is the registered trademarks of Microsoft® Corporation. [. . . ] When a device is selected in the list it's MAC address also appears in the Device MAC Address field in the device information area 2 below the list. Device Port No. The MIDI port number of the corresponding device. When a device is selected in the list it's MIDI port number also appears in the Device Port No. field in the device information area 2 below the list. [Device Port No. ] The MIDI port number of the device selected in the Target Device List can be set via this menu. The MIDI port number also functions as device ID number. It should be set to "1" for DME64N/24N units, or to "2" for DME8i-C, DME8o-C, DME4io-C, and SP2060 units. n The MIDI port number must be set properly or communication with the device will not be possible. [New] Button Click this button to add a new device to the list. Edit the device's parameters as required via the fields in the device information area 2 below the list, then click the [APPLY] button to add the specified device. [Duplicate] Button This button adds a device to the list by copying the data from the currently selected device. Edit the new device's parameters as required via the fields in the device information area 2 below the list, then click the [APPLY] button to add the specified device. [Apply] Button Click the [Apply] button after editing the Device Name, Device IP Address, Device MAC Address, or Device Port No. parameters to actually apply the changes. Also, devices added to the Target Device List 1 by pressing the [NEW] or [DUPLICATE] buttons will only actually be registered for communication with the YAMAHA DME-N Network Driver when the [Apply] button is pressed. [Remove] Button Deletes the selected device from the list. If the removed device is not the lowest device in the list, all devices below the removed device will be shifted upward to maintain the continuity of the list. 3 [Advanced Settings] Button Opens the "Advanced Settings" window. This window provides access to advanced settings. For details refer to the "Advanced Settings" section. [Remove ALL] Button Deletes all devices from the list. [Undo] Button This button provides a one-step undo function that allows you to undo a single operation and revert to the previous state. The "TCP/IP Filtering" dialog will be displayed. Select "Permit All" for TCP Ports, then click [OK]. 9 Enter your computer's IP address into [IP address], the Gateway's IP address into [Default gateway], and "255. 255. 255. 0" into [Subnet mask]. n When installing on the same subnet as the DME unit(s), set the gateway's host address to 254. 4 5 6 7 10 11 Click [OK]. Restart your computer. The display returns to the "Advanced TCP/IP Settings" dialog. Click [OK] to return to the "Internet Protocol (TCP/ IP) Properties" dialog. 8 Click [Use the following IP address] on the [General] tab. 8 DME Designer Installation Guide Windows 2000 1 Select [Start] [Settings] [Control Panel] [Network and Dial-Up Connections] [Local Area Connection]. The "Local Area Connection Status" dialog box will be displayed. Click [Properties] on the [General] tab. The "Local Area Connection Properties" dialog box will be displayed. Click [Internet Protocol (TCP/IP)] on the [General] tab, then click [Properties]. The "Internet Protocol (TCP/IP) Properties" dialog box will be displayed. Click [Advanced. . . ], then [Properties] on the [Options] tab. The "TCP/IP Filtering" dialog will be displayed. [. . . ] · You may not use the SOFTWARE to distribute illegal data or data that violates public policy. · You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation. Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe. · Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner. [. . . ]