User manual YAMAHA DME64NV1

[. . . ] DIGITAL MIXING ENGINE Owner's Manual EN Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] SLOT-1, SLOT-2, SLOT-3, SLOT-4: A card installed in the corresponding I/O slot is currently selected for MIDI input. 2 NO T E Panel Operation and Displays 1 3 Edit using the "List Parameters" editing procedure described on page 41. NOTE When the DME64N/24N is functioning as the zone master and is connected to a computer running the DME Designer application via USB, the MIDI port being used by the DME Designer will not be available. This page will not appear on the ICP1 display. 1 Card Name The name of the installed card appears here. 3 Format Displays the 88. 2/96 kHz audio signal transfer mode. The input setting is on the left and the output setting is on the right. No Display (Default): 44. 1/48 kHz audio signal transfer. SP (Double Speed): An 88. 2/96 kHz capable card is installed, allowing direct transfer at 88. 2 or 96 kHz. CH (Double Channel): A 44. 1/48 kHz card is installed, and 88. 2 or 96 kHz audio is transferred by using two 44. 1/48 kHz channels to transfer each channel of 88. 2/96 kHz audio. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the card. 2 DAW Specifies the type of MIDI device (DAW control surface, etc. ) to be connected. The choices are OFF, TYPE1, and TYPE2. OFF: Use this setting when any MIDI device other than a general-purpose ProTools controller (HUI protocol) or general-purpose Logic or Cubase controller (Mackie control protocol) is to be connected. TYPE1: Use this setting when a general-purpose ProTools controller (HUI protocol) is to be connected. TYPE2: Use this setting when a general-purpose Logic or Cubase controller (Mackie control protocol) is to be connected. Edit using the "List Parameters" editing procedure described on page 41. Refer to the DAW controller owner's manual as well as the DME Designer manual for setup details. 52 DME64N/24N Owner's Manual Utility Displays NO T E "DAW" stands for "Digital Audio Workstation. " ProTools, Logic, and Cubase are DAW applications, and this parameter provides direct compatibility with a number of physical controls surfaces that are available for use with these DAW software packages. GPI Setup (GPI) Page Input calibration parameters for the [GPI] connector. NOTE This page will not appear on the ICP1 display. The following parameters are available when the DAW parameter is set to OFF. 3 CH Specifies the device's MIDI transmit and receive channel: 1 ~ 16. Edit using the "List Parameters" editing procedure described on page 41. 4 Program Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI program change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 5 Control Change Turns transmission and reception, the omni mode, and echo ON or OFF for MIDI control change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. 6 Parameter Change Turns transmission and reception, and echo ON or OFF for MIDI parameter change messages. Move the cursor to the required parameter, then press the [ENTER] button to alternately turn ON and OFF. ] To reset the calibration, use the [E [ ] [ ] [F ] buttons to select ALL to reset all inputs, or select an individual input from 1 to 16 to be reset, then press the [ENTER] button. 2 MAX Sets the maximum calibration value. To set the MAX value, use the [E [ ] [ ] [F ] ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MAX value to the current input voltage. 3 MIN Sets the minimum calibration value. [. . . ] Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Belgium Rue de Geneve (Genevastraat) 10, 1140 - Brussels, Belgium Tel: 02-726 6032 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]