User manual YAMAHA DPX-1300 THROW-CHART

[. . . ] 12 For Canadian customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES003. 13 14 15 IMPORTANT! Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the bottom of the unit. Retain this Owner's Manual in a safe place for future reference. [. . . ] Press the STANDBY/ON button on the projector or the STANDBY ( · A confirmation message is displayed. · To cancel the procedure, wait a while or press the MENU button. Press the STANDBY/ON button on the projector or the STANDBY ( ) button on the remote control again. · The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS indicator blinks green. Wait about one minute for the STATUS indicator to be off and the POWER indicator to be steadily lit in red. · During this one minute period, the intake fan and exhaust fan rotate to cool the lamp. · Do not unplug the power cable while the STATUS indicator is blinking. Unplugging the power cable immediately after use may cause a breakdown. · The fan may make loud sounds during cooling; this is not a malfunction. STANDBY( )button STANDBY/ON button 18 7 Menu Menu overview Menus are not displayed when no signal is received by the projector. IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE *1 sRGB COLOR TEMP. *1 0 - 60 ± 30 DEFAULT, 0 - 10 ON , OFF CONTRAST R HIGH CONTRAST B MID BRIGHTNESS R LOW BRIGHTNESS B CUSTOM 0 - 20 ± 10 0 - 10 DEFAULT, DYNAMIC, CINEMA1, CINEMA2 0 - 60 0 - 60 ± 30 ± 30 SATURATION *1 *3 *1 *3 HUE *3 SHARPNESS *1 GAMMA SET UP KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN HIDE SCREEN COLOR LAMP MODE LOCATION ± 20 ON , OFF OFF, 5, 10, 15, 30, 60 min ON , OFF BLUE, BLACK BRIGHT, CINEMA FRONT/TABLE, REAR/TABLE, REAR/CEILING, FRONT/CEILING INITIAL MENU POSITION PROGRESSIVE MODE *3 COLOR SYSTEM *3 ASPECT UPPER LEFT, LOWER RIGHT AUTO , VIDEO AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 DEFAULT, NORMAL, SQUEEZE, ZOOM, THROUGH *2 LANGUAGE RESET ALL , ENGLISH, ESPANÕL, DEUTSCH, FRANÇAIS, ITALIANO, EXECUTE SIGNAL HORIZ. POSITION*3 VERT. POSITION *3 *3 PHASE *3 TRACKING *3 D-SUB INPUT *3 SET UP LEVEL SYNC NOISE MASK *3 0 - 999 *2 0 - 999 *2 0 - 31 0 - 9999 *2 RGB, COMPONENT OFF, 3. 5%, 7. 5% ON OFF BEGIN END CLAMP POSITION CLAMP WIDTH LPF *3 0 - 99 0 - 99 0 - 63 1 - 63 ON , OFF A/D SETTING *3 EXECUTE *2 *2 After selecting the items marked with , press the ENTER button. *1: Not available when sRGB is set to ON. Wait about 10 minutes, plug the power cable in, and try again. 20 Menu settings Set the following items on their relevant menus. IMAGE menu TV60 IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE sRGB COLOR TEMP. SATURATION HUE SHARPNESS GAMMA 0 0 DEFAULT OFF MID 0 0 0 DEFAULT 2. SETUP menu TV60 SETUP KEYSTONE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN HIDE SCREEN COLOR LAMP MODE LOCATION 0 OFF OFF ON BLUE BRIGHT FRONT/TABLE 3. INITIAL menu TV60 INITIAL MENU POSITION PROGRESSIVE MODE COLOR SYSTEM ASPECT LANGUAGE RESET ALL UPPER LEFT AUTO AUTO DEFAULT ENGLISH EXECUTE 4. SIGNAL menu TV60 SIGNAL HORIZ. POSITON PHASE TRACKING D-SUB INPUT SET UP LEVEL SYNC NOISE MASK A/D SETTING 78 22 0 0 RGB 7. 5% OFF EXECUTE 1. IMAGE menu ITEM CONTRAST BRIGHTNESS WHITE ENHANCE SETTING 0 ­ 60 ±30 DEFAULT 0 ­ 10 sRGB COLOR TEMP. ON / OFF HIGH MID LOW CUSTOM SATURATION HUE SHARPNESS GAMMA 0 ­ 20 ±10 0 ­ 10 DEFAULT DYNAMIC CINEMA1 CINEMA2 FUNCTION Use to adjust the contrast of the projected image (see page 24). Use to adjust the brightness of the projected image (see page 24). The appropriate white enhance value is automatically selected depending on the input signal. Use to adjust the white level of the projected image (see page 24). Select whether or not to project emphasizing on the color reproducibility. Select for a high color temperature (see page 25). [. . . ] · Remove any objects blocking the ventilation grilles. Steady green or Steady red Steady red Blinking green Abnormal when it occurs except while shutting down. The protection circuit is working or the lamp is in an abnormal condition. · Wait until the STATUS indicator goes out, then press the STANDBY/ON button. · If the above solution is not effective, replace the lamp. Change with a new lamp if this problem recurs. Steady green Blinking green/red Lamp operation time warning. [. . . ]