User manual YAMAHA DRC-20

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] For more about EtherSound connections, refer to pages 24 and 28. Introduction to the DME Satellite 6 [REMOTE] Connector This 9-pin D-SUB connector allows connection to a Yamaha AD824 or AD8HR remote head amplifier or an RS-232C/ RS-422 compatible controller such as those from AMX or Crestron. You can also connect a Yamaha PM5D or DM2000 and control the internal head amps of the DME8i-ES/ DME4io-ES. See "Remote Connection ([REMOTE] Connector)" on page 26 for connection details. Precautions for Using a Rack-mounted DME Satellite If several DME Satellite units (or a DME Satellite unit together with other devices) are installed in a poorly-ventilated rack, the heat generated by each unit may raise the temperature inside the rack, preventing the DME Satellite from performing as designed. When mounting DME Satellite units in a rack, please leave one rack space vacant for every two units. You can attach a ventilation panel to this space or leave it open to prevent excessive heat build-up. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1. 6m3/min or more and static pressure of 5mmH2O or more. Foreword Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References Connecting to a Computer USB Connection To connect multiple DME Satellite units to a network, you must assign appropriate IP addresses and make other network settings on all units. To achieve this, you need to connect the [USB] connector of one of the DME Satellite units to the USB port of the computer using USB cables, install USB-MIDI Driver and DME Designer on the computer, then assign the IP addresses to the DME Satellite units from DME Designer. N OT E · Refer to the "DME Setup Manual" (PDF file) for details on installing USB-MIDI Driver and DME Designer. · Make sure that the USB-MIDI Driver's THRU setting is "OFF. " · Refer to "Network Settings" on page 19 for more information on assigning IP addresses from DME Designer. USB connections can be used in the following three ways: (1) Set up the network (e. g. , assign a unique IP address to each DME Satellite) from DME Designer. (2) Control the DME Satellite from DME Designer. (3) Connect to any individual DME Satellite and control that DME Satellite unit by transmitting MIDI commands from a MIDI sequencer or similar software. N OT E · The computer on which DME Designer is running can be connected to either the group master or a slave DME series unit. · Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds. The maximum length of a cable between a switching hub and the DME Satellite is 100 meters. Due to the quality of cables and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases. Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. · If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting. · You can also connect a supported controller such as the AMX or Crestron, and control the DME Satellite remotely. For details, refer to "Connecting to an External Device" on page 26. DME8i-ES/DME8o-ES/DME4io-ES Owner's Manual 21 References Other Functions Connecting to an External Device Audio I/O Connection Connecting to a Computer DME64N/24N (IP address: 192. 168. 0. 250) (Master ID: 7) Controls and Connectors Foreword Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References Connecting to a Computer Control from a computer with a different subnet Device Group Group Master DME Satellite (IP address: 192. 168. 0. 5) Ethernet Cable Port settings · Destination network address: 192. 168. 0. 0 · Subnet mask: 255. 255. 255. 0 · Gateway: 192. 168. 0. 254 Switching Hub Ethernet Straight Cable Ethernet Cable Ethernet Straight Cable DME Satellite (IP address: 192. 168. 0. 3) (Master ID: 5) Router or Layer-3 Compliant Switching Hub Ethernet Straight Cable Computer SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192. 168. 0. 12) (Master ID: 5) 22 DME8i-ES/DME8o-ES/DME4io-ES Owner's Manual Connecting to a Computer Connecting multiple device groups Device Group 1 Group Master DME Satellite (IP address: 192. 168. 0. 2) Ethernet Cable Ethernet Cable Device Group 2 Group Master DME Satellite (IP address: 192. 168. 0. 3) Switching Hub Switching Hub Ethernet Straight Cable Ethernet Straight Cable Ethernet Straight Cable Ethernet Cable SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER DME Satellite (IP address: 192. 168. 0. 40) (Master ID: 2) DME Satellite (IP address: 192. 168. 0. 10) (Master ID: 3) DME8i-ES/DME8o-ES/DME4io-ES Owner's Manual 23 References Other Functions Connecting to an External Device Computer (IP address: 192. 168. 0. 1) Audio I/O Connection Connecting to a Computer DME64N/24N (IP address: 192. 168. 0. 100) (Master ID: 2) Ethernet Cable DME64N/24N (IP address: 192. 168. 0. 200) (Master ID: 3) Controls and Connectors Introduction to the DME Satellite Foreword Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References Audio I/O Connection Digital Audio Connection (EtherSound Connectors) You can use the DME Satellite's EtherSound connector to input and output digital audio signals, control signals, and word clock signals. When connecting DME Satellites, make daisy-chain connections between the EtherSound [OUT] connector [IN] connector, and the [OUT] connector [IN] connector. Audio signals and word clock signals can also be input and output between EtherSound compatible devices and devices such as mixers in which the MY16-ES64 card has been installed. Input and output of audio signals and word clock signals can be specified using the "AVS-ESMonitor" application software made by AuviTran SARL. [. . . ] 14 User Defined buttons (User Defined parameters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DME8i-ES/DME8o-ES/DME4io-ES Owner's Manual 45 Other Functions Audio I/O Connection Connecting to a Computer Controls and Connectors Foreword Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References 46 DME8i-ES/DME8o-ES/DME4io-ES Owner's Manual MEMO For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]