User manual YAMAHA DSP-E200

[. . . ] DSP-E200 Natural Sound Digital Sound Field Processor 4 Programs for Digital Sound Field Processing 2 Programs for Dolby Surround (DOLBY PRO LOGIC and ENHANCED) Center and Rear Channel Power Amplifier 25W (8) RMS Output Power, 0. 08% THD, 20-20, 000 Hz (Center) 25W + 25W (8) RMS Output Power, 0. 3% THD, 1, 000 Hz (Rear) Automatic Input Balance Control for Dolby Surround Test Tone Generator for Easier Speaker Output Balance Adjustment 3 Center Channel Modes Remote Control Capability Thank you for selecting this YAMAHA digital sound field processor. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN OWNER'S MANUAL CONTENTS Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Profile of This Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See pages 13­15. ) 2Display panel Displays your selection on the DSP or other informations. 9DELAY TIME Adjusts delay time. (See page 15. ) 3TAPE MONITOR Used when you have connected the tape deck to this unit's TAPE terminals to select that tape as the source. (See page 14. ) 0FRONT EFFECT LEVEL Adjusts effect sound output level at front speakers. (See page 16. ) ACENTER LEVEL Adjusts center speaker sound output level. (See page 16. ) 4TEST Used for speaker balance adjustment. (See pages 11­12. ) BREAR LEVEL Adjusts rear speaker sound output level. (See page 16. ) 5CENTER MODE Selects center speaker mode. (See page 11. ) CMUTING When pressed, mutes the volume level. To resume original volume level, press this again. While muting, the indicator on the VOLUME control flashes on and off continuously. 6DIGITAL SOUND FIELD PROCESSING programs Selects a program from the digital sound field processor. (See pages 13­15. ) 7MASTER VOLUME Turns the master volume level up/down. 10 ADJUSTMENT BEFORE OPERATION SPEAKER BALANCE ADJUSTMENT Using the built-in test tone generator, this procedure lets you adjust the sound output level balance between the front, center, and rear speakers. With this adjustment, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of digital sound field processor. The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. Otherwise, the result may not be satisfactory. 2 3 1 54 1 4 VOLUME Select the center mode depending on your speaker configuration. (Refer to "SPEAKER CONFIGURATION" on page 5. ) NORMAL 0 CENTER MODE -- dB Set to the " WIDE PHANTOM On the feature of each mode, refer to the "Note" shown below. " position. 2 Set on the POWER of this unit and the amplifier etc. POWER 5 3 DIGITAL SOUND FIELD PROCESSING TEST DELAY TEST ms FCR NORMAL PRO LOGIC CONCERT MONO ROCK CONCERT ENHANCED VIDEO MOVIE CONCERT HALL Flashes on and off continuously. OFF PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE ROCK CONCERT CONCERT HALL DOLBY SUR. Note In step 4, when you select the center mode, note the following. For 5 speaker configuration) NORMAL: Select this mode when you use the center speaker smaller sized than the front speakers. In this mode, the bass tone will be output from the front speakers. WIDE: Select this mode when you use the center speaker approximately same sized as the front speakers. For 4 speaker configuration) PHANTOM: Select this mode when you do not use the center speaker. The center sound will be output from the left and the right front speakers. 11 6 Turn up the volume by using the remote control transmitter. You will hear a test tone (like pink noise) from the left front speaker, then the center speaker, then the right front speaker, then the rear speakers, for about two seconds each. [. . . ] Then, turn the MUTING switch off with the remote control transmitter and adjust the volume. Turning the unit off and then on will reset the protection circuit. If the problem persists, the cords may be defective. If the problem persists, the cords may be defective. [. . . ]