User manual YAMAHA DTS70E

[. . . ] (FCC DoC) FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] Click the black area of the ruler to move the project cursor (the vertical black line) to that position. Ruler Inspector 2 3 Make sure the [Record Enable] button for the track to be recorded is turned on. If the [Record Enable] button is off, click it to turn it on. Play the instrument to be recorded, and adjust the AUDIOGRAM GAIN controls and LEVEL controls so that the Clipping indicator never lights. <Transport panel> Clipping indicator 12 DTS70E Owner's Manual Quick Guide Recording and Playback 4 1 Click the Transport panel [Record] button to begin recording. When recording is started the project cursor will begin moving to the right and a box that displays the recording results will be created. <Transport panel> Select [Mixer] from the [Devices] menu to open the Mixer window. The overall playback level will be displayed via the master section bus level meter on the right side of the mixer window, and the channel level will be displayed via the channel strip level meter. NOTE To hear the playback sound via the AUDIOGRAM interface, adjust the volume with the DAW control and MASTER LEVEL control. The playback level will approximately match the recording level when the DAW control is set to about 1 o'clock. Rewind Forward Stop Record Start Level meter Recording results Bus level meter 5 2 3 Play the part. When you finish recording the track, click the Transport panel [Stop] button. To hear playback of the track you have just recorded, use either the Transport panel [Rewind] button or the ruler to rewind to the beginning of the recorded section, then click the Transport panel [Start] button. To save the project select [Save] from the [File] menu and enter a file name before actually saving the file. Save your project frequently to insure against losing large amounts of data if a problem occurs. Repeat steps 1 through 5 to record further material on the same track. To record additional material on a different track, select a new track and repeat the record procedure. 6 7 Recording with maximum quality and minimum noise: For optimum sound quality with minimum noise, the AUDIOGRAM signal levels should be set as high as possible without clipping. To achieve the best balance between S/N ratio and dynamic range, adjust the level so that the input channel PEAK indicator 9 lights only occasionally and briefly on the highest input transients. DTS70E Owner's Manual 15 Controls and Functions 7 COMP Control Adjusts the amount of compression applied to the channel. As the knob is turned to the right, the interface automatically raises the compression ratio while adjusting the output gain accordingly. The result is smoother, more even dynamics because louder signals are attenuated while the overall level is boosted. NOTE Avoid setting the compression too high, as the higher average output level that results may lead to feedback. CAUTION 8 MONO/STEREO Switch This switch allows channels 1 and 2 to be used either as separate mono channels or as a stereo pair. When set to MONO ( ), channels 1 and 2 function as independent mono channels feeding both the L and R STEREO OUT jacks 3. When set to STEREO ( ), input channels 1 and 2 function as a stereo pair: the channel 1 signal feeds the L STEREO OUT jack and the channel 2 signal feeds the R STEREO OUT jack. · Be sure to leave this switch off ( ) if you do not need phantom power. · When turning the switch on, be sure that only a condenser microphone is connected to the channel 1 MIC/INST input jack. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones or instruments with the phone jack, however, as these will not be affected by phantom power. · To prevent damage to speakers, be sure to turn off power amplifiers (or powered speakers) before turning this switch on or off. We also recommend that you set the MASTER LEVEL control to the minimum position. [. . . ] Tel: 714-522-9011 THE NETHERLANDS/ BELGIUM/LUXEMBOURG FRANCE Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 Yamaha Musica Italia S. P. A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 Yamaha Música Ibérica, S. A. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 Philippos Nakas S. A. The Music House 147 Skiathou Street, 112-55 Athens, Greece Tel: 01-228 2160 Yamaha Scandinavia AB J. [. . . ]