User manual YAMAHA DTX550K ASSEMBLY MANUAL

[. . . ] Alternately, to prevent damaging your floor, lay the cardboard of the included packages, etc. on the floor before assembling the two parts shown in the circles in Figure 1. Figure 1: Unit Standard Assembly · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. [. . . ] Slide pipe so the further end of pipe will slide outward about 7 cm from the joint part with the standing vertical pipe. Tighten the six knobs loosened and fix the position of pipes and . Insert the rubber foot on each further end of pipe and . PCY155 (Cymbal Pad) (1) RHH135 (Real Hi-Hat Pad) (1) Stopper (2) Figure 6: Rack Assembly-4 PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. Assembling the Electronic Drum Rack 1 H C J D KP65 (Kick Pad) (1) Hi-Hat Clutch (1) Stand Base (1) CAUTION Take out the electronic drum rack from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the electronic drum rack. The pipe ends may injure your fingers. E Drum Key (1) HS650A (Hi-Hat Stand) (1) WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Figure 3: Rack Assembly-1 · Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. · Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury. · Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury. · If this product is used with the electronic drum rack or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. · Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. · When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. Doing so may result in injury or damage/deterioration to the product. · Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. *1 YAMAHA logo label on the curved pipe is facing the opposite side. *2 The knob is on the opposite side of the pipe. 8 9 Cable Band (1) See Figure 6. Loosen the two knobs ((h) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. [. . . ] Tighten the clamp bolt and attach the 3-zone drum pad XP100SD firmly. %1 Hi-Hat %2 KP65 (Kick Pad) #1 DTX500 + Module stand #2 Clamp #3 Knob Attach the module stand (#1) onto the clamp (#2). Tighten the knob (#3) and fix the position. ^1 DC IN terminal (12V) ^2 Cable clip ^3 Standby/On Switch 4 5 6 1 Connecting the pads to the Trigger Module Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 26: DTX500 (Rear panel) Make sure to turn the power off Standby/ On Switch (^3) is set to the standby position ( )). Figure 30: Cable clip (DTX500 rear panel) 2 2 7 Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent Figure 23: KP65 Assembly scratching the surface. Attach the AC adaptor to connect to a power source. Insert the DC plug into the DC IN terminal (^1) and twist the cable around the cable clip (^2) to prevent the DC plug from falling out. Mounting the PCY135 and PCY155 (Cymbal pads) on the electronic drum rack Figure 15: Pads Assembly-3 Figure 16: Cymbal holder-1 Figure 31: Using Cable Band Figure 27: 9-channel Snake Cable 3 Use the cable bands to bind the cables to the pipes at the points shown with the circles. @0 @1 @2 @3 @4 1 PCY135 PCY155 Cymbal holder Wing nut Felt washer #4 #5 #6 #7 #8 2 Body Base Wing bolt Spring washer Washer See Figure 16. [. . . ]