User manual YAMAHA DTX700K ASSEMBLY MANUAL

[. . . ] Mount the three tom pads on the rack's clamp rods. · Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. · Be careful with the edges of the Cymbal Holders and the Tom Holders. [. . . ] If necessary, use clamp bolts A to E to adjust the Mounting the snare pad Clamp bolt NOTICE · Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. · Do not step on or place heavy objects on the product. · Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. · When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. 1. Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns). Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) height and angle of the snare pad. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt A Clamp bolt C Clamp bolt C Clamp bolt D Clamp bolt B * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Continued on other side Mounting the drum trigger module and cymbal pads PCY135 Assembling the kick pad Mounting the cymbal pads PCY135 1. Using a tuning key, loosen the stopper's key bolt. 5. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper's key bolt using a tuning key. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. [. . . ] Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. Bolt cover 9 8 7 No 6 Connection 5 4 3 2 1 Straight plug names (as shown on stickers) DTX700 jack names 1: qSNARE 2: wTOM1 3: eTOM2 4: rTOM3 5: tRIDE 6: yCRASH1 7: iHI-HAT 8: HI-HAT CONTROL 9: oKICK/!0 Pad unit Stopper [9-channel snake cable] Straight plugs Drum trigger module + module stand Felt pad Insert Cymbal holder Bolt cover Pin L-shaped plugs SNARE TOM1 TOM2 TOM3 RIDE CRASH HI HAT HH CON KICK 3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE Stopper Clamp bolt Holder clamp * When assembling the bolt cover, turn until it no longer rotates. Cymbal holder NOTICE Excessive bending can damage the pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. Assembling the hi-hat stand 6 5. [. . . ]