User manual YAMAHA DTXPRESS IV SPECIAL SET ASSEMBLY MANUAL

[. . . ] They may be pinched, resulting in injury. Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. [. . . ] Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. *1 Use cable bands to bind cables to pipes in " *2 Not this manual. (Spare bands are included. ) Figure 6: Rack Assembly-4 RHH135 (Real Hi-Hat Pad) (1) Hi-Hat Clutch (1) Stand Base (1) Assembling the Rack System 1 Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system. WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury. Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury. If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. Doing so may result in injury or damage/deterioration to the product. The rack may overturn or be damaged, resulting in injury. The pipe ends may injure your fingers. Figure 3: Rack Assembly-1 HS650A (Hi-Hat Stand) (1) Stereo Phone Cable (1) Cable Band (1) 8 9 10 *1 YAMAHA logo label on the red curved pipe is facing the opposite side. *2 The knob is on the opposite side of the pipe. See Figure 6. Loosen the two knobs ((h) on the upper left) aligned at the base of pipe , and move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((j) on the middle right) aligned at the base of pipe and the in a knob ((k) on the lower right) of the slim pipe supporting pipe . [. . . ] Tighten the clamp bolt and attach the 3-zone drum pad TP100 firmly. %1 Hi-Hat %2 KP65 (Kick Pad) #1 DTXP4 + Module stand #2 Clamp #3 Knob Attach the module stand (#1) onto the clamp (#2). Tighten the knob (#3) and fix the position. 4 5 6 Connecting the pads to the Trigger Module Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 25: DTXP4 (Rear panel) ^1 Power supply jack (DC IN 12V) ^2 Cable clip ^3 Power switch 1 2 Make sure to turn the power off (the Standby/ On switch (^3) is set to the standby position ( )). Figure 29: Cable clip (DTXP4 rear panel) Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent scratching the surface. 2 7 Figure 22: KP65 Assembly Figure 26: 9-channel Snake Cable Figure 30: Using Cable Band Attach the AC adaptor to connect to a power source. Insert the DC plug into the power supply jack (^1) and twist the cable around the cable clip (^2) to prevent the DC plug from falling out. Mounting the PCY135 and PCY155 (Cymbal pads) on the rack system Figure 14: Pads Assembly-3 Figure 15: Cymbal holder-1 3 Use the cable bands to bind the cables to the pipes at the six points shown with the circles. * Leaving the cable slacked may interfere with your performance. @1 @2 @3 @4 #4 #5 #6 #7 #8 Body Base Wing bolt Spring washer Washer * Each straight plug is labeled indicating the input jacks to which they are to be connected. 1 PCY155 Cymbal holder Wing nut Felt washer See Figure 15. [. . . ]