User manual YAMAHA E30E

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] USB-1, USB-2: The corresponding USB port is selected for MIDI input. Slot1 [Slot1 ~ Slot4 (DME64N)]: A card installed in the corresponding I/O slot is currently selected for MIDI input. Edit using the "List Parameters" editing procedure described on page 38. NOTE When the DME64N/24N is functioning as the device group master and is connected to a computer running the DME Designer application via USB, the MIDI port being used by the DME Designer will not be available. Ext HA Ctrl (External head amp control) Displays/sets the type of connection to be used for external head amp control. OFF: Select "OFF" when this function is not to be used. Remote (422): Allows remote head amp control. Always use this setting when a remote head amp unit (AD8HR, AD824) is connected. Also, don't change the setting while a remote head amp is connected. Doing so can damage the unit. COM Displays/sets the type of connection to be used for DME communication Protocol. Normally, set this to "OFF". DME64N/E30E Owner's Manual 49 Panel Operation and Displays Utility Displays Protocol (MIDI Protocol Setup) Displays/sets the protocol to be used for communication with devices connected via MIDI. The available settings are: MIDI, DAW(Type1), and DAW(Type2). To reset the calibration, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to reset all inputs, or select an individual input from 1 to 16 to be reset, then press the [ENTER] button. MAX Sets the maximum calibration value. To set the MAX value, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MAX value to the current input voltage. MIN NOTE This page will not appear on the ICP1 display. Card Name The name of the installed card appears here. Sets the minimum calibration value. To set the MIN value, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MIN value to the current input voltage. Reset Resets the installed card. Calibration Info Shows the calibration settings as well as the current input voltage. Format Displays the 88. 2/96 kHz audio signal transfer mode. The input setting is on the left and the output setting is on the right. No Display (Default): 44. 1/48 kHz audio signal transfer. SP (Double Speed): An 88. 2/96 kHz capable card is installed, allowing direct transfer at 88. 2 or 96 kHz. CH (Double Channel): A 44. 1/48 kHz card is installed, and 88. 2 or 96 kHz audio is transferred by using two 44. 1/48 kHz channels to transfer each channel of 88. 2/96 kHz audio. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the card. DME64N/E30E Owner's Manual 51 Panel Operation and Displays Utility Displays Head Amplifier Setup (HA) Page Provides access to the head amplifier settings. Refer to "REMOTE Connection" on page 28 for head amplifier control signal connection. NOTE This page will not appear on the ICP1 display. WCLK (AD8HR/AD824 only) Specifies the word clock signal to be used by the head amplifier(s). Available settings of the AD8HR are "D OUT A, " "WCLK IN, " "INT44. 1K, " "INT48K, " "INT88. 2K, " and "INT96K. " D OUT A: Sets the word clock signal at the digital input as the master clock of the AD8HR. [. . . ] 32 Z zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DME64N/E30E Owner's Manual 75 MEMO 76 DME64N/E30E Owner's Manual MEMO DME64N/E30E Owner's Manual 77 MEMO 78 DME64N/E30E Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]