User manual YAMAHA EF3000ISEB

[. . . ] Generator OWNER'S MANUAL EF3000iSE EF3000iSEB LIT-19626-01-20 7CH-28199-10 AE00002 INTRODUCTION Congratulations on your purchase of your new Yamaha. This manual will provide you with a good basic understanding of the operation and maintenance of this machine. If you have any questions regarding the operation or maintenance of your machine, please consult a Yamaha dealer. CODE AE00012 SERIAL No. IDENTIFICATION NUMBER RECORDS Record your Primary I. D. , and serial numbers in the spaces provided, to assist you in ordering spare parts from a Yamaha dealer. [. . . ] Pull slowly on the recoil starter until it is engaged, then pull it briskly. After the engine starts, warm up the engine until the engine does not stop when the choke knob is returned to the original position. Push the choke knob back to the original position. 704-018 ­ 16 ­ AE01000 APPLICATION RANGE AC DC Power factor 1 0. 8­0. 95 0. 4­0. 75 (Efficiency 0. 85) Rated voltage 12V Rated current 12A EF3000iSE EF3000iSEB ­2, 800W ­2, 240W ­950W NOTE: 9 "­" means below. 9 Application wattage indicates when each device is used by itself. 9 The simultaneous usage of AC and DC power is possible but total wattage should not exceed the rated output. EX: Generator rated output Frequency Power factor 1. 0 AC 0. 8 DC -- 2, 800VA ­2, 650W ­2, 100W 144W (12V/12A) q 760-026 9 The overload indicator light 1 comes on when total wattage exceeds the application range. (See page 19 for more details. ) cC Be sure the total load is within generator rated output otherwise generator damage will occur. NOTE: Some precision equipment is voltage sensitive and may require a more uniform voltage supply than portable generators provide. Examples include some medical equipment, personal computers, and some inverters that sense peak and RMS voltage values. Consult the precision-equipment vendor before relying on any portable generator to provide power to such equipment. ­ 17 ­ AE01023 CONNECTION Alternating Current (AC) cC 9 Be sure all electric devices including the lines and plug connections are in good condition before connection to the generator. 9 Be sure any electric devices are turned off before plugging it in. 9 Be sure the total load is within generator rated output. 9 Be sure the receptacle load current is within receptacle rated current. Wind the power lead 2 or 3 turns around handle. Plug in to the AC receptacle. 761-081 761-082 4. Make sure the AC pilot light is on. 1 AC pilot light 5. Turn the economy control switch to the "I" (ON) position and turn on any electric devices. q 760-027 1 q I (ON) 763-129a NOTE: The economy control switch must be turned to "3" (OFF) when using electric devices that require a large starting current, such as a compressor or a submergible pump. ­ 18 ­ AE01087 q 760-026 Overload indicator light The overload indicator light 1 comes on when an overload of a connected electrical device is detected, the inverter control unit overheats, or the AC output voltage rises. The electronic breaker will then activate, stopping power generation in order to protect the generator and any connected electric devices. The AC pilot light (green) will go off and the overload indicator light (red) will stay on, but the engine will not stop running. When the overload indicator light comes on and power generation stops, proceed as follows: 1. Turn off any connected electric devices and stop the engine. [. . . ] Turn the fuel cock knob to "OFF". Start the engine and leave it run until it stops. This will burn any remaining fuel in the carburetor. AE01079 712-028a ENGINE 1. Remove the spark plug, pour about one tablespoon of SAE 10W30 or 20W40 motor oil into the spark plug hole and reinstall the spark plug. [. . . ]