User manual YAMAHA EL200E

[. . . ] SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded / stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. [. . . ] This is the same procedure as the one when you start recording. The small bars that flash across the display indicate that the M. D. R. is recording the registrations and being set up for normal recording; pressing the STOP button interrupts this process. SONG REPEAT FROM TO SONG COPY SONG DEL. PAUSE STOP PLAY SONG SELECT RECORD CUSTOM PLAY TEMPO FORMAT MUSIC DISK RECORDER 37 5 Recalling Recorded Registrations (and Bulk Data) The registrations (and bulk data) recorded to song numbers in the above operation can be loaded back to the Electone by simply selecting the appropriate song number and pressing the PLAY button. When the operation has been completed, the M. D. R. returns to STOP status. 1 2 6 Music Disk Recorder Insert the disk and select the song number you want to load back to the Eelectone. Press the PLAY button. Using More Than 8 Registrations The M. D. R. makes it possible to use more than 8 registrations (8 Registration Memory locations) in a performance. A disk can accommodate 40 song numbers and each song number can contain 8 registrations. To play a performance using more than 8 different registrations: 1. First record the registrations you need into several song numbers on the M. D. R. (You should also try to record them in the order that you'll use them, if possible. ) 2. During the performance, after all 8 registrations from a certain song number have been used, select the next song number and press the PLAY button on the M. D. R. This replaces all 8 registrations in Registration Memory with the new ones from the selected song number. By repeating the above steps, you can run through an entire performance without having to change the panel settings. 6 Replacing Registrations The M. D. R. also lets you change the registrations of an existing song without changing the performance data. The procedure is the same as that of Recording Registrations mentioned in the previous page. 38 7 Playback You can play back your recorded performance by simply pressing the PLAY button. Registrations and other data will be recalled to the Electone. NOTE: You can play back the commercially available XG song (SMF format 0 or 1). If the disk contains normal Electone song data and XG data, it accommodates each data in the two different locations separately. If you insert the disk containing those two types data, you can access the location of normal Electone song data as the default. However, you can exchange the location and access the XG data. In doing this, press the STOP button while holding down the SHIFT button. Each press of the STOP button while holding down the SHIFT button alternately selects Electone song data and XG data. In the case of Electone song data In the case of XG data STOP SHIFT Underline indicates the LED shows XG song number. NOTE: Although EL-200 itself doesn't have the detailed Registration Shift settings and sequence programming functions, you can load those data in EL-200 and use them using M. D. R. [. . . ] LOWER KEYBOARD VOlCE . . . . . . . . . . . . . . . . . . . . . . . . . . 19 13 30 49 47 13 73 IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your plug proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. [. . . ]