User manual YAMAHA ELB01E3

[. . . ] ELB-01 Assembly Instructions Carefully read these instructions BEFORE assembling the Electone. Be careful not to confuse any of the parts, and be sure to install all parts in the correct direction by following the procedures given below. [. . . ] When you take out the Speaker Unit, always hold the bottom of the Speaker Unit, not holding the Grill Net. Music Rest Main Unit Long screws (ø6 X 25 mm): 4 pcs. Dust Cover Styrofoam pads Take out the styrofoam pads, and place the Main Unit on top of the pads. Short screws (ø5 X 12 mm): 8 pcs. Pedalboard cord clamps: 2 pcs. Speaker Unit Screw caps: 4 pcs. Grill Net Attached to the Speaker Unit Sideboard (Left) Sideboard (Right) Bench Bench Board Pedalboard Unit Legs: 4 pcs. EN ELB-01 Assembly Instructions 1 3 3-1 3-2 Mount the Sideboards onto the Pedalboard unit. Be sure not to confuse the Right and Left Sideboards. Raise the Pedalboard as shown in the illustration below. Position each screw hole on both the Pedalboard and Sideboards as shown in the illustration and mount the Sideboards onto the Pedalboard using the 4 short screws (2 screws on each Sideboard). 4-3 While holding the Sideboard(s) to the Speaker unit, fasten the four short screws from the rear, to secure the Speaker unit to the Sideboards. Cover the four screw holes on the rear side with the corresponding screw caps. Push the Sideboard toward the Speaker unit Push the Sideboard toward the Speaker unit Push the Sideboard toward the Pedalboard Short screws Screw caps Screw caps Short screws Short/black screws 3-3 Stand the Pedalboard after securing the screws. 5 Mount the Main Unit. As shown in the illustration, hold the Main unit horizontally (with two people), and place it on the front side of the Speaker unit so that the arm at the bottom of the Main unit comes in front of the Sideboards, then slide it to the rear side. 5-1 4 Mount the Speaker Unit onto the Sideboards. Remove the Grill Net from the Speaker Unit. 4-1 4-2 With the help of another person, hold the Speaker unit horizontally, and slide it from the rear into place along the brackets. 1. Place down so that the arm comes in front of the Sideboard Arm 2. Slide to the rear side Take care not to drop the Main unit or to pinch your finger(s) between the Speaker unit and Main unit. Take care not to drop the Speaker unit or to pinch your finger(s) between the Speaker unit and Sideboard. 2 ELB-01 Assembly Instructions 5-2 Use the four long screws to fasten the Main unit to the Sideboards as shown in the illustration. 7 Connect the Pedalboard cord and Speaker cord to the Main Unit. Make sure that the latches on each plug of the cords face toward you, and connect them to each socket securely. Long screw Speaker cord Pedalboard cord 8 8-1 Long screw Fix the Pedalboard cord to the Sideboard using the Pedalboard cord clamps. Affix the two Pedalboard cord clamps to the rear side of the Speaker unit and the lower inside of the Left Sideboard as shown in the illustration. 6 Fit the Grill Net onto the Speaker. First, align the net with the bottom line, then secure it to the speaker assembly. 8-2 Insert the Pedalboard cord in the clamps. Fasten the Grill Net by inserting the knobs into the holes. Shut the clamp after inserting the cord. ELB-01 Assembly Instructions 3 9 Place the music rest on the Electone. After completing the assembly, please check the following items. · Are there any parts left over?· Is the Electone clear of doors and other movable fixtures? [. . . ] Be sure to put the washer between each leg and nut as shown. Leg Washer Bench board Nut 4 ELB-01 Assembly Instructions U. R. G. , Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2005 Yamaha Corporation WF43900 510MWAP3. 3-01A0 Printed in China [. . . ]