User manual YAMAHA EM100II

[. . . ] Make sure that the voltage selector is set for the voltage in your area. The voltage selector is set at 240V when the unit is initially shipped. To change the setting use a "minus" screwdriver to rotate the selector dial so that the correct voltage appears next to the pointer on the panel. For information on assembling the keyboard stand, refer to the instructions at the end of this manual. EN SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. [. . . ] You can also use the [DATA ENTRY] dial and the [ENTER] button to select a Bank. Press one of the green-lit numbered buttons ([1] ­ [8]) in the Registration Memory section. Confirming the Registration Memory Information You can call up the information display to take a look which Voices and Style are memorized to the [1] ­ [8] buttons of a Registration Memory Bank. 2 Press the [7] (INFO. ) button to call up the information display. You can instantly call up the information display of the currently selected Registration Memory Bank by pressing the [DIRECT ACCESS] button and one of the REGISTRATION MEMORY [1] ­ [8] buttons in sequence. 3 2 By using the TAB [E][F] buttons, you can switch between the two information display pages: information for the Registration Memory [1] ­ [4] buttons and information for the [5] ­ [8] buttons. NOTE 3 Press the [F] (CLOSE) button to close the information display. If some Voice part is set to off (CVP509/505), the Voice name for corresponding part is shown in gray. (On the CVP-503/501, the Voice part name for corresponding part is shown in gray. ) CVP-509/505/503/501 Owner's Manual 81 Registration Memory ­ Saving and Recalling Custom Panel Setups ­ 1 6 NOTE Simultaneously press the REGIST BANK [+] and [-] buttons to call up the Registration Bank Selection display, then use the [A] ­ [J] buttons to select the desired Bank. Advanced Features Refer to the Reference Manual on the website, Chapter 6. Disabling recall of specific items: Calling up Registration Memory numbers in order: [FUNCTION] [E] REGIST SEQUENCE/FREEZE/ VOICE SET TAB [E][F] FREEZE [FUNCTION] [E] REGIST SEQUENCE/FREEZE/ VOICE SET TAB [E][F] REGISTRATION SEQUENCE 6 Registration Memory ­ Saving and Recalling Custom Panel Setups ­ 82 CVP-509/505/503/501 Owner's Manual USB Audio (CVP-509/505/503) ­ Playback and Recording Audio Files ­ The convenient USB Audio function allows you to play back audio files (WAV or MP3) stored to a USB flash memory device--directly from the instrument. Moreover, since you can record your performances and recordings as audio data (. WAV) to a USB flash memory device, it is possible to play back the files on computer, share them with your friends, and record your own CDs to enjoy as well. Playing Back Audio Files CVP-509 EM100II CVP-503 CVP-501 Try playing back audio files from USB flash memory on this instrument. File formats that can be played back . wav 44. 1 kHz sample rate, 16 bit resolution, stereo CVP-509 EM100II CVP-503 CVP-509 EM100II NOTE The instrument cannot be play back DRM protected files. . mp3 44. 1/48. 0 kHz sample rate, 64-320 kbps and variable bit rate, mono/stereo 7 NOTE 1 Press the [USB] button to call up the Playback display (AUDIO PLAYER display). Before using a USB flash memory, be sure to read "Connecting a USB Storage Device" on page 106. 2 2 Press the [8 ] (FILE SELECT) button to display the audio files saved to the connected USB flash memory. CVP-509/505/503/501 Owner's Manual 83 USB Audio (CVP-509/505/503) ­ Playback and Recording Audio Files ­ Connect the USB flash memory device containing the audio files to play back to the [USB TO DEVICE] terminal. 3 Press one of the [A] ­ [J] buttons corresponding to the file you want to listen to. 4 5 Press the [EXIT] button to return to the Playback display (AUDIO PLAYER display). Press the [2 ] (F/ II) button to play back. CAUTION Never attempt to disconnect the USB flash memory or turn the power off during playback. Doing so may corrupt the USB flash memory data. 7 USB Audio (CVP-509/505/503) ­ Playback and Recording Audio Files ­ 84 CVP-509/505/503/501 Owner's Manual Playback-related Operations You can stop, pause, select, rewind, and forward by using the [1 ] ­ [6 ] buttons. Moreover, you can set the REPEAT mode by pressing the [7 ] button and adjust the volume by pressing the [7 ] button. · Playing back audio files repeatedly Press the [7 ] (REPEAT) button then set the REPEAT mode of the audio file by using the [7 ] buttons. To close the setting display, press the [8 ] (CLOSE) button. OFF SINGLE ALL RANDOM Plays through the selected file, then stops. Plays through the selected file repeatedly. Continues playback through all the files in the folder containing the current file repeatedly. · TUNE Pitch-related settings (tuning, transpose, etc. ). · EFFECT Selects effect type and adjusts its depth for each part (page 92). · EQ Adjusts equalization parameters to correct the tone or timbre of the sound. NOTE · CMP (CVP-509) This is the Master Compressor setting which determines the dynamics of overall sound. See page 93. The Master Compressor is not applied to USB audio playback and Metronome sound. 88 CVP-509/505/503/501 Owner's Manual 3 Press the [MIXING CONSOLE] button repeatedly to call up the MIXING CONSOLE display for the relevant parts. The part name is indicated at the top of the display. NOTE The Style/Song part components are the same as those that appear in the display when you press the panel [CHANNEL ON/OFF] button once or twice. Song, Style, MIC (CVP-509/505/503), Keyboard parts (Left, Right 1, 2) Rhythm 1, 2, Bass, Chord 1, 2, Pad, Phrase 1, 2 Song channels 1 ­ 8 Song channels 9 ­ 16 4 5 Use the [A] ­ [J] buttons to select a parameter, then use the [1 ] ­ [8 ] buttons to set the value for each part. · To save the PANEL PART display settings: Register them to Registration Memory (page 79). · To save the STYLE PART display settings: Save them as Style data. [FUNCTION] [F] DIGITAL REC MENU [B] STYLE CREATOR 2. Press the [EXIT] button to close the RECORD display. Press the [I] (SAVE) button to call up the Style Selection display for saving your data, then save it (page 68). · To save the SONG CH 1-8/9-16 display settings: First register the edited settings as part of the Song data (SETUP), then save the Song. [FUNCTION] [F] DIGITAL REC MENU [A] SONG CREATOR EF 2. [. . . ] 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Europe Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. Tel: 714-522-9011 HONG KONG Tom Lee Music Co. , Ltd. 11/F. , Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 ITALY Yamaha Musica Italia S. P. A. [. . . ]