User manual YAMAHA EM95

[. . . ] · The screen displays as illustrated in this owner's manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer. · Future upgrades of application and system software and any changes in specifications and functions will be announced separately. · Windows is a registered trademark of Microsoft Corporation in the U. S. · Apple, Mac and Macintosh are trademarks of Apple Inc. , registered in the U. S. [. . . ] This is linked with the STEREO fader in the STEREO A/B channel strip of the PM5D panel. The current value is shown in the numerical box immediately below. A level meter is shown beside the fader. E CUE This button cue-monitors the signal of the STEREO A/B channel. This is linked with the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel. If SOLO is active, this will function as SOLO. 5 38 EM95/DSP5D Editor Owner's Manual STEREO to MATRIX 2 1 3 4 A MATRIX send level Here you can adjust the send levels of the signals sent from the STEREO A/B channels to the MATRIX bus. B Pair This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the heart symbol to enable/disable pairing. C ON (MATRIX send on/off) This is an on/off switch for the signal sent from the STEREO A/B channel to the MATRIX bus. D POINT (Send point) Selects the point from which the signal is sent from the STEREO A/B channel to the MATRIX bus. You can choose PRE FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immediately after the STEREO [ON] key). 39 EM95/DSP5D Editor Owner's Manual Patch Editor window Here you can assign the input/output port for each channel, its direct output, and its insert-in/out. This window is divided into INPUT PATCH, OUTPUT PATCH, INPUT INSERT PATCH, OUTPUT INSERT PATCH, DIRECT OUT PATCH, and PATCH LIST pages. To switch pages, click the tabs shown in the upper part of the window. INPUT PATCH page Here you can select the input port that is assigned to the input of each input channel. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's INPUT PATCH screen. NOTE · VIRTUAL SOUNDCHECK is a display-only function. · In DSP5D Editor, VIRTUAL SOUNDCHECK will be lit only if you operate the PM5D with the PM5D and DSP5D connected. 40 EM95/DSP5D Editor Owner's Manual OUTPUT PATCH page Here you can select the output port that is assigned to the input of each output channel. To switch channels, use the SELECT button or the / buttons at left and right. You can also edit the channel name in the text box. B PAIR Indicates the pair status of the two selected channels. If an input channel is selected, you can click the heart symbol to enable/disable pairing. C LINK Specifies whether movement of the sound image will be linked for the two selected channels. If this button is on, the sound image of the two channels will be linked according to the link pattern you select using LINK PATTERN SELECT buttons 1­8. D LINK PATTERN SELECT These buttons select link patterns 1­8. The currently selected pattern is shown graphically at the left. E SURROUND MODE This indicates the currently selected surround mode. You can click this area to switch the mode. 45 EM95/DSP5D Editor Owner's Manual 8 9 J 6 7 K F DIVERGENCE These controls specify the proportion at which the signals are sent to each surround bus when the input channel is positioned in the center. The operable parameters will change as follows, according to the surround mode that is currently selected. · Surround mode= 3-1ch/5. 1ch The Div knob will be operable, allowing you to adjust the front divergence. Use this knob to specify the proportion (0­100) at which a signal positioned in the center will be sent to the center bus (C) and the left/right buses (L, R). · Surround mode= 6. 1ch The F knob and R knob will be operable, allowing you to adjust the front and rear divergence separately. Use these two knobs to specify the proportion (0­100) at which a signal positioned in the center will be sent to the center buses (C, Bs) and the left/right buses (L, R, Ls, Rs). In addition, a LINK button that links front and rear divergence is displayed between the F knob and R knob. If you turn the LINK button on, the value of the F knob will be copied to the R knob, and the two knobs will be linked. G LFE (Low Frequency Effect) Use the LFE knob to adjust the level of the signal sent from the input channel to the subwoofer LFE bus, over a range of ­ to 0 dB. [. . . ] 22 INSERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 M/S DECODE . . . . . . . . . . . . . . . . . . . . . . . . . . 36 MIX channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 34, 37, 38 STEREO A/B channel . . . . . . . . . . . . . . [. . . ]