User manual YAMAHA EMT-1

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Resume" setting in DME Designer to set up the DME Satellite so that at startup it will recall the scene selected before you turned off the power to the device. · If "Last Mem. Resume" is set to ON, the unit will back up data to the internal memory periodically. In this case, do not turn off the power to the unit within five (5) seconds after you operate any parameters. CAUTION DME8i-C/DME8o-C/DME4io-C Owner's Manual 19 References Other Functions Connecting to an External Device Audio I/O Connection Connecting to a Computer Controls and Connectors Foreword Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References Controls and Connectors Rear Panel DME8i-C 1 3 4 5 6 7 9 MAC ADD * XX XX XX XX XX XX * RS-232C RS-422 2 1 3 4 5 6 8 7 DME8o-C MAC ADD * XX XX XX XX XX XX * RS-232C RS-422 2 1 3 4 5 6 8 7 ) 9 DME4io-C MAC ADD * XX XX XX XX XX XX * RS-232C RS-422 2 1 [AC IN] Connector Connect to the AC mains using the supplied AC power cord. First connect the power cord to the DME Satellite, then insert the power cord plug into an AC outlet. Even when the power switch is turned off, electricity is still flowing to the product all the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. 8 ) 4 Dip Switch This 6-bit dip switch enables you to select the [REMOTE] connector function or initialize the DME Satellite, depending on its setting at the startup of the device. To switch between RS-232C and RS-422 for the [REMOTE] connector function, turn off the power to the device, set the dip switch as shown below, then turn on the power to the device again. See page 35 for the DME Satellite initialization procedure. RS-232C RS-232C CAUTION RS-422 RS-232C 2 Ground Screw The supplied AC power cable is a 3-wire type, so if the AC outlet used is properly earthed the DME Satellite will be earthed as well. Hum and interference may by further reduced in some cases by also connecting the earth screw to an earth point. 3 [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or to another DME series unit in the network. You cannot specify 0, 127, or 223 through 255 for the 1st octet of the network address. You can specify the following range of values for the 4th octet. Master : 2-253 Slave : 3-253 NO T E · Subnet mask is fixed at 255. 255. 255. 0. · The network address of Gateway is the same as that of IP address. The host address of Gateway is automatically set to 254. · Assign each of DME series units a unique IP address so that there are no duplicates. Assigning duplicate IP addresses may cause serious network problems. · You cannot make any network settings while using the DME Designer application on-line. To make network settings, first set DME Designer off-line. Refer to the DME Designer Owner's Manual for details. · If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D, you must specify a value of 2 as the fourth octet of the group master DME Satellite's IP address. [. . . ] 10 W Warning Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Z zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 50 DME8i-C/DME8o-C/DME4io-C Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]