User manual YAMAHA EMX62M

[. . . ] Owner's Manual Keep This Manual For Future Reference. E The Owner's Manual Revisions E Révisions du Mode d'emploi de l'EMX62M F Thank you for purchasing the Yamaha EMX62M Powered Mixer. Parts of the EMX62M owner's manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner's manual. Nous vous remercions d'avoir opté pour le mélangeur amplifié EMX62M de Yamaha. Nous avons apporté une série de révisions au Mode d'emploi de l'EMX62M. [. . . ] 20 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Block & Level Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 EMX62M--Owner's Manual 6 EMX62M Quick Guide EMX62M Quick Guide The following steps (1-5) explain the basic connection and operation of the EMX62M. Also, please read "Front and Rear Panel" and "Basic Operation" following this Quick Guide section to learn more about using the EMX62M. Connecting a microphone Make sure that the power is turned off to the EMX62M. Connect a microphone to the Low-Z jack of channel 1-4. EMX62M Microphone STEP 1 Connection Connecting speakers Using speaker cables, connect each speaker to the SPEAKERS 1 and 2 jack on the rear panel of the EMX62M. Using a condenser microphone Turn on the PHANTOM switch (located in the upper right corner on the panel). EMX62M EMX62M · The EMX62M is a monaural mixer. The same signal will be output from all SPEAKERS jacks on the rear panel. You do not need to differentiate right from left speakers. · You may connect to either of the two jacks on the speakers. · Be sure to use a cable designed for speaker connection. PHANTOM switch · Do not connect or disconnect a condenser microphone while the power to the unit is on and the PHANTOM switch has been turned on. Never connect the speakers in the manner shown below. Otherwise, the EMX62M's built-in power amplifier will be damaged. Connecting a CD player, MD player, and/or cassette deck Connect a CD player or MD player to the 2TR IN jacks. Refer to the operation manual of the corresponding device for more information on the input and output of the device. EMX62M EMX62M CD player Recorder (Cassette, DAT, MD) EMX62M--Owner's Manual EMX62M Quick Guide 7 · To connect a second player, use the LINE jack or HiZ jack. · You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the Low-Z jack of a channel, you cannot connect a player to the Hi-Z jack of the channel. · Connect a recorder to the REC OUT jacks. Connecting an electric acoustic guitar or electric bass Connect an electric acoustic guitar or electric bass to the Super Hi-Z jacks. You can use either or both of the 1 and 2 jacks. EMX62M Connecting an electronic musical instrument To the EMX62M's LINE jacks, you can connect an electronic musical instrument such as a synthesizer, drum machine, signal processor connected to an electric guitar, etc. Refer to the diagram below to make a stereo connection from the output jacks (such as L/MONO and R) of an electronic musical instrument to the LINE jacks in stereo. EMX62M Synthesizer, Drum machine, Guitar processor If you wish to connect multiple instruments, make a monaural connection as shown below. EMX62M Electric-acoustic guitar Electric bass · If you wish to use a guitar signal processor or bass effect unit, connect them to the Hi-Z jack or LINE jack. You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the LowZ jack of a channel, you cannot connect the effect unit to the Hi-Z jack of the channel. · You can also use the Hi-Z jacks and Super Hi-Z jacks to connect multiple instruments. You cannot use the Hi-Z jack and the Low-Z jack for the same channel at the same time. If a microphone has already been connected to the Low-Z jack of a channel, you cannot connect an instrument to the Hi-Z jack of the channel. EMX62M--Owner's Manual 8 EMX62M Quick Guide STEP 2 Power on 1 Turn on the power to all external devices connected to the EMX62M. 2 Make sure that the MASTER controls in the MONITOR section and the MAIN section are set to "0, " then press the POWER switch on the EMX62M to turn on the power. EMX62M STEP 4 Applying built-in effects 1 Turn on the ON switch in the DIGITAL EFFECT section. 2 Select one of three effect types, then press the switch. [. . . ] · If the device is not ventilated sufficiently, refer to the cautions given at the beginning of this manual and take appropriate measures to insure adequate ventilation. · If the load impedance (including a short) is too low, refer to the section on rear panel (page 14) and change the connections so that the impedance is correct. Inspect the connections, and correct any faulty connections. Please contact your dealer. Connections between devices have come loose. Other Other Unbalanced sound output from the speakers The speaker's protection circuit has Turn off the power to the EMX62M, or lower the volume been activated due to excessive input level. [. . . ]