User manual YAMAHA FIELDROTATION

[. . . ] All rights reserved. 1 Installing Field Rotation See the ADD-ON EFFECTS Installation Guide for more information on installing Field Rotation. Using Field Rotation As with other effects, you can recall and edit the Field Rotation program on the console or in Studio Manager. The basic operation is as follows: 1 2 3 4 5 6 Select one of the internal effects processors. Patch the signal to and from the currently selected effects processor. Select and recall Field Rotation. n When you recall the program, all effects processor outputs will be muted temporarily. Locate the Effects Edit page. [. . . ] You can change this value by double clicking in the number display section of the Field Rotation window, then typing a number from the keyboard, or by dragging vertically with the mouse. In the Generic Editor window and console, the [R. RATIO] knob can be used to change the current data. The [RRAT KY1] knob can be used to change KEY 1, and the [RRAT KY2] knob can be used for KEY 2. 5 OFFSET Changes the coordinates for the center point of the virtual sound field. You can change this value by double clicking in the number display section of the Field Rotation window, then typing a number from the keyboard, or by dragging vertically with the mouse. In the Generic Editor window and console, the [X OFFSET] and [Y OFFSET] knobs can be used to change the current data. The [XOFS KY1] and [YOFS KY1] knobs can be used to change KEY 1, and the [XOFS KY2] and [YOFS KY2] knobs can be used for KEY 2. DEGREE Changes the angle of rotation of the virtual sound field. This parameter is valid only when the Parameter View is [EDIT]. You can change this value by double clicking in the number display section of the Field Rotation window, then typing a number from the keyboard, or by dragging vertically with the mouse. This parameter can also be adjusted using the [DEGREE] knob in the Generic Editor window and console. STEP Changes the interval in degrees of rotation by which the Degree parameter changes. You can change this value by double clicking in the number display section of the Field Rotation window, then typing a number from the keyboard, or by dragging vertically with the mouse. This parameter can also be adjusted using the [DEG STEP] knob in the Generic Editor window and console. DISTANCE/[DISTANCE] Knob Adjusts the strength of attenuation in volume caused by distance. By changing the value for DISTANCE, you can adjust the difference in volume between when the sound source is near or far away. The amount of attenuation strengthens (reduces the volume of a distant sound) as this value is increased This parameter can also be adjusted using the [DISTANCE] knob in the Generic Editor window and console. Rotation Mode These modes relate to rotation. [CAV] Button: Constant Angular Velocity (the speed of rotation through the degrees of the angle is constant). [CLV] Button: Constant Linear Velocity (the speed of rotation around the circumference of the circle is constant). 4 SURROUND MODE SURROUND MODE Display When the surround mode is 6. 1, "6. 1" is displayed. "3-1" is displayed for 3-1 surround, and "5. 1" is displayed for all others. [DIV] Knob/[DIV F] Knob Sets right and left for the front center signal, along with the percentage sent to the center channel. When the surround mode in the Field Rotation window is 6. 1, [DIV. F] is displayed. [DIV. F] is always displayed in the Generic Editor window and console. DIV/DIV F Display Displays the DIV/DIV F value. You can change this value by double clicking, then typing from the keyboard, or by dragging vertically with the mouse. If the setting is zero, only L/R is used. If 50 is set, the ratio between L/R and the center will be 50:50. When 100 is set, the signal will go to the center channel only. 6 [DIV R] Knob Sets right and left for the rear center signal, along with the percentage sent to the center channel. [. . . ] GO&REV: Continuously changes back and forth between the KEY 1 size and the KEY 2 size. LOOP: After changing from the KEY 1 size to the KEY 2 size, it returns to the KEY 1 size and repeats. Speed Slider/[RADI SPD] Knob Adjusts the speed of automation. R. RATIO This sets the aspect ration of the virtual sound field. KEY 1 Aspect ratio at the start point of automation. It then makes a revolution in the reverse direction and repeats the process. LOOP: When the Interpolation Mode is Linear, it loops by moving from the KEY 1 position to the KEY 2 position, then jumping back to the KEY 1 position before repeating. [. . . ]