User manual YAMAHA FLUTES/PICCOLOS

[. . . ] Doing so may result in injury or damage/deterioration to the product. If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur. Do not step on or place heavy objects on the product. Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. [. . . ] Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. * To customers who purchased a Pads Set, please refer to the attached "Accessories List" sheet included with the Pads Set when confirming package contents. Q TP65 main unit x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 w TP65S main unit* x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 e TP100 main unit* x 1, t clamp bolt x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 r TP120SD main unit* x 1, y stereo phone cable x 1, u Owner's Manual (this sheet) x 1 TP65/65S Drum Pad Size: ø220 x 61(H) mm (excluding the clamp bolt) Weight: 980g (including the clamp bolt) Sensor System: [TP65] Trigger sensor (piezo) x 1 [TP65S] Trigger sensor (piezo) x 1, rim switch (2 zones) x 1 Output jack: [TP65] Standard mono phone jack [TP65S] Standard stereo phone jack TP100 Tom Pad (10") with rod clamp Size: 297 (W) x 313 (D) x 74 (H) mm (Control knob and clamp bolt not included. 2kg Sensor System: Trigger sensor (piezo) x 1, rim switch (2 zones) x 1 Output jack: Standard stereo phone jack TP120SD Snare Pad (12") Size: 349 (W) x 364 (D) x 69 (H) mm (Control knob not included. * Specifications are subject to change without notice. Si ce produit est utilisé avec le système de racks ou le support de cymbales, ne placez pas le rack ou le support sur une surface inclinée ou instable ou sur des marches. The function of the TP series pads varies according to which INPUT number on the DTX Series Drum Trigger Module the pad is connected. The chart below describes its function in relation to input numbers. * For the users of the TP65/65S, connect to the input that is used for the tom pad on your drum trigger module. (Refer to the Owner's Manual that came with your module. (TP100/120SD) Increase the output level using the level adjustment knob on the pad. Hitting the pad once produces multiple sounds (double triggering) (TP100/120SD) Decrease the output level using the level adjustment knob on the pad. Too high of a level adjustment setting causes the drum module to produce multiple sounds, because the large signal produced by the high settings sustains for too long of a time. Is the TP100/120SD connected to the correct input number on the module (DTXTREME IIs/DTXPRESS IV) using the supplied parallel type stereo phone cable?The Pad control function can only be used with INPUTs 1­5 on a DTXTREME IIs or INPUT 1 on a DTXPRESS IV. (See "Pad-to-Input Matching Chart" above. ) The Pad control function is not available when a mono phone cable is used. * Using any stereo phone cable other than the supplied parallel type stereo phone cable can result in improper function of the pad control function. Also, please refer to the Owner's Manual that came with your DTX Series Drum Trigger Module for more information regarding the problems described above and any other problems that you may be experiencing. If a solution can not be found to the problem after consulting the manuals, please contact the dealer from whom you purchased the product. The pad controller on the TP100/120SD can be used with INPUTs 1-5 on the DTXTREME IIs or INPUT 1 on the DTXPRESS IV. [. . . ] If the output level is too high, the pad's dynamic range (the difference between loud and soft sounds) will be reduced and problems such as double triggering (multiple triggers being produced by a single stroke) may occur. Controls the level of the trigger output from the TP100/120SD. Rotate the level adjustment knob w to the right (looking at the knob from above) to increase the output level, or to the left to decrease it. The pad's output level should be adjusted depending on how hard you hit the pad, or to adjust the pad's dynamic range, or to better match the pad to the type of DTX Series Drum Trigger Module you are using. [. . . ]