User manual YAMAHA FX CRUISER SHO-2008

[. . . ] 2008 WaveRunner FX SHO FX Cruiser SHO OWNER'S/OPERATOR'S MANUAL U. S. A. Edition READ THIS MANUAL CAREFULLY BEFORE OPERATION! LIT-18626-07-87 F1W-F8199-10 Important manual information EJU30180 To the owner/operator Thank you for choosing a Yamaha watercraft. This owner's/operator's manual contains information you will need for proper operation, maintenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. [. . . ] (1) Squeeze the QSTS selector lock lever and check that it returns smoothly to its original position when released. shifted from neutral to bow up or bow down. (2) Check that the QSTS selector turns smoothly when the lever is squeezed and check that the selector locks in place at each position when the lever is released. If the mechanism does not work properly, have a Yamaha dealer service it. EJU32650 (3) Check that the angle of the jet thrust nozzle changes when the QSTS selector is Jet intake Carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the jet intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump. In some cases, the engine may overheat because of lack of cooling water, and damage to the engine could result. Cooling water is fed to the engine by the jet pump. (See page 106 for jet intake cleaning procedures. ) EWJ00470 WARNING G Keep away from the intake grate while the engine is on. Items such as long hair, loose clothing, or PFD straps can be- 69 Operation G come entangled in moving parts, resulting in severe injury or drowning. Stop the engine and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have collected around the jet intake. EJU32670 Switches ECJ00410 CAUTION: Do not run the engine for more than 15 seconds when checking the switches on land without supplying water, otherwise the engine could overheat. Check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. Push the start switch to start the engine. As soon as the engine starts running, push the engine stop switch to verify that the engine stops immediately. Restart the engine, and then pull the engine shut-off cord to remove the clip from the engine shut-off switch to verify that the engine stops immediately. (See pages 33 to 34 for information on proper operation of the start switch, the engine stop switch, and the engine shut-off switch. ) 3 4 1 EJU32660 5 2 1 2 3 4 5 Start switch Engine stop switch Engine shut-off switch Clip Engine shut-off cord Engine shut-off cord Check that the engine shut-off cord is not frayed or broken. If the cord is damaged, replace it; never try to repair it or tie it together. EJU36890 Cooling water pilot outlets Check that water comes out from the port (left) cooling water pilot outlets while the en- 70 Operation gine is running and the watercraft is in the water. (See page 34 for more information. ) EJU32740 Operation EWJ00510 WARNING Before operating your watercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or function that you do not fully understand. Failure to understand how the controls work could cause an accident or prevent you from avoiding an accident. ECJ00460 EJU32710 Multifunction information center Check the multifunction information center for proper operation. (See page 45 for information on proper operation of the multifunction information center. ) CAUTION: Make sure that the stern drain plugs are tightened securely before launching the watercraft. EJU36660 Engine break-in The engine break-in period is essential to allow the various components of the engine to wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer component life. ECJ00440 CAUTION: Be sure to check the engine oil level before operating the watercraft for the first time. (See page 63 for engine oil checking procedures. ) 71 Operation (1) Launch the watercraft and start the engine. (See page 72 for engine starting procedures. ) (2) For the first 5 minutes, run the engine at trolling speed only. For the 30 minutes of operation after that, keep the engine speed below 5000 r/min. [. . . ] 109 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Switches, right handlebar . . . . . . . . . . . . . . . . . . . . . . . . . 34 T Throttle cable, checking and adjusting . . . . . 95 Throttle lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]