User manual YAMAHA FX550

[. . . ] [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Limited Guarantee for European Economic Area (EEA) and Switzerland Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. [. . . ] The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha. The following are excluded from this guarantee: a. Periodic maintenance and repair or replacement of parts due to normal wear and tear. Damage resulting from: (1) Repairs performed by the customer himself or by an unauthorised third party. (2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer's responsibility to ensure the product is adequately packaged when returning the product for repair. (3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha's instructions on the proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used. (4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha's control. (5) Defects of the system into which this product is incorporated and/or incompatibility with third party products. (6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland. Refer to the above chart. · When installing your FX550/NS-IC800 in-ceiling speakers, be aware of the product weight (See specification page) and the sturdiness of the material into which you are installing the speaker. · Be aware of any concealed studs, electrical wiring or plumbing in the ceiling into which you are installing the speakers. If you are not sure of a safe way to install these speakers, consult a professional installer or a building contractor. CAUTION · When installing the speaker, do not touch the woofer or tweeter units with your hands or expose them to excessive physical shock. If they are dented or bent, the sound will be distorted. NOTE · If you wish to paint the speaker grille, refer to page 6 "PAINTING THE SPEAKER GRILLE" before proceeding. 3 En English How to install This is the recommended installation procedure when the material of the installation location is plasterboard. 5 1 2 Position the cutout template where you are installing the speaker. Trace a line around the template with a pencil. The mark for the center of the hole is also required. Insert the tip of a keyhole saw into the pilot hole, and then cut all of the way around the circular outline. WARNING · When using a keyhole saw or cutting tool, use safety goggles for eye protection and be sure to observe all safety precautions. 6 3 Drill the pilot hole at the center mark made on the ceiling. Pull the speaker cable out of the hole which you have cut. · Leave some extra length of cable when pulling the cable out. 7 WARNING · When using a drill or cutting tool, use safety goggles for eye protection and be sure to observe all safety precautions. Connect the speaker cable to the speaker. · For detailed instructions, refer to page 6 "CONNECTING YOUR AMPLIFIER/RECEIVER". 8 Place the speaker into the ceiling. 4 To check the space behind the hole, insert a bent sturdy wire (such as a coat hanger) into the hole, and then slowly rotate the wire to check for any obstruction. · If there is any obstruction, patch the hole and select another location. CAUTION · When installing the speaker, do not touch the tweeter dome or woofer cone directly. · Make sure that mounting clamps are turned inward when installing the speaker in a ceiling. 360° 4 En 9 Insert the speaker into the hole. Loosen four screws approximately one turn counterclockwise. It will allow the clamps to open easily. 10 Adjust the angle of the tweeter. · Gently press the outer edge of the tweeter housing toward the listening position. · This tweeter movable angle is about 15° in multiple directions. Loosen *15° *15° * Tweeter movable angle Evenly tighten each of the four mounting screws clockwise using a Philips screwdriver. (At this time, these four mounting clamps open in the ceiling. [. . . ] This may cause breakage of the mounting clamps and fracture of the wallboard. · We recommend using only hand tools as power screwdrivers may over-tighten the screws. Should you use a power screwdriver be certain to select a very low torque setting to prevent damage to the speaker or to the wallboard. · Make sure that none of the screws are loose and that there are no gaps between the speaker and the ceiling. CAUTION · Be very careful when removing the grille, as it may fall or cause injury. [. . . ]