User manual YAMAHA GO44

[. . . ] Owner`s Manual EN SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over , or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! [. . . ] However, to take full advantage of the advanced routing, sample rate switching, and other control features, please install the included Control Panel. 1. Insert the included "TOOLS for GO44/GO46" CD-ROM in the CD-ROM drive of your computer. 2. Double-click on the CD-ROM drive icon and open [GO44Driver_] [GO44 Setup. pkg] to start the InstallShield Wizard. 3. The welcome message of the InstallShield Wizard appears. Select the hard disk drive where the Mac OS is installed as the destination for the installation. Click [Install] to start the installation. Click [Restart] to complete the installation. NOTE For information about the Control Panel, see page 19 of the PDF manual. Assigning the GO44 as the default system audio device (Mac OS X) If you would like to use the GO44 not only for specific audio applications, but as your default Mac OS X audio device, select the GO44 audio driver in the [Sound] control panel as the default device for audio output. 12 Connectors and controls Front Panel 2 1 A PHONES jack Output for a 1/4" stereo headphone jack. This signal output applies not only to that of the OUTPUT 1/2 jacks (see Rear Panel), but also allows monitoring of other audio channels using the GO44 Control Panel. (See page 19. ) B VOLUME control Adjusts the output level of the PHONES jack. Turn this control to the right to increase the level, and left to decrease it. Rear Panel 3 C DC IN jack 4 5 6 7 Connects the AC power adaptor to this jack. D IEEE1394 (FireWire) port Connects the GO44 system to your computer using the included IEEE1394 (FireWire) cable. E MIDI / DIGITAL jack For connection of the included I/O cable (page 14), allowing input/output of digital audio and MIDI data. 13 Connectors and controls F INPUT 1/2 jacks The GO44 System features two high-quality analog mono inputs. The connections have been designed for balanced/unbalanced phone 1/4" jacks. The input levels for these jacks can be selected from three different gain settings, HIGH, MID, and LOW. Refer to page 19 for details on how to make these settings. G OUTPUT 1/2 jacks The connections have been designed for balanced/unbalanced phone 1/4" jacks for main output. You can connect mixers, powered speakers, or amplifiers. The analog outputs operate with instrument-compatible levels of 2. 0 Vrms. I/O cable 8 H MIDI IN jack 9 J K Connects MIDI devices such as MIDI keyboards and DAW controllers. For connecting MIDI devices, connect the MIDI OUT terminal of the MIDI device to this jack using a MIDI cable. I MIDI OUT jack Connects to MIDI devices such as synthesizers and tone generators. For connecting MIDI devices, connect the MIDI IN terminal of the MIDI device to this jack using a MIDI cable. This can also be used as a MIDI Thru terminal, for MIDI sequence software that allows routing of incoming MIDI data through the OUT jack, using a Thru (or MIDI Echo) function. J DIGITAL IN jack This coaxial type digital audio jack is for the digital input of audio signals. The interface can receive sample rates of up to 24-bit/96 kHz. [. . . ] Nusantik Gedung Yamaha Music Center, Jalan Jend. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 SPAIN/PORTUGAL Yamaha-Hazen Música, S. A. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 BRAZIL Yamaha Musical do Brasil Ltda. Reboucas 2636-Pinheiros CEP: 05402-400 Sao Paulo-SP. [. . . ]