User manual YAMAHA GQ1031BII

[. . . ] Numeric keys Chapter 1 Getting Started 6 Putting the Disklavier in Standby Mode Tap on [More] in the toolbar, then on [Standby] in the More screen that appears. To reactivate your Disklavier. . . Reactivating from Standby Mode (page 8) Chapter 1 Getting Started 7 Reactivating from Standby Mode Use the following screen to reactivate your Disklavier from Standby mode. Slide the switch to the right. Switch Reactivates your Disklavier from Standby mode. Chapter 1 Getting Started 8 2 Song Playback Introduction 9 Selecting a Song Tap on [Select] in the toolbar. Tap on the desired source/media. Source list Media list Next, select an album. Selecting an album (page 11) Chapter 2 Song Playback 10 Selecting a Song (continued) Tap on the desired album. [Source] Returns to source selection. Album list [Media] Returns to media selection. Album list Next, select a song. Selecting a song (page 12) Chapter 2 Song Playback 11 Selecting a Song (continued) Tap on the desired song. [Album] Returns to album selection. Song list [Album] Returns to album selection. Song list* * Displaying the list may take time if there are many songs. The selected song is played back. [. . . ] Operation during playback (page 13) Chapter 2 Song Playback 12 Operation during Playback Tapping on the screen during song playback shows the song control panel for various operations. * Display of the song control panel cycles on and off every time you tap on the screen. Tap on the screen during playback. Song title [ ] (skip / fast forward) Skips to the next song when tapped briefly (less than one second). Fast-forwards through the current song when tapped for a longer period (at least 1 second). [ ] (play / pause) Starts or pauses playback. Song position Displays the playback position. ] (skip back / rewind) [ Skips to the previous song when tapped briefly (less than one second). Rewinds through the current song when tapped for a longer period (at least one second). * Operations in this application may not always take effect on your Disklavier immediately. Chapter 2 Song Playback 13 Operation during Playback (continued) Tap on the screen during playback. Repeat mode Cycles through the repeat mode. : Repeat off : Single repeat mode : All repeat mode : Random repeat mode Main volume Adjusts the main volume. Quiet status*1 Cycles through the quiet status. : Acoustic mode : Quiet mode : Headphone mode*2 *1 You cannot change quiet status when connected to some models of the Disklavier E3 and Disklavier Control Unit DKC-850. [Audio] Adjusts the volume of software (audio CD, etc). Chapter 5 Other Functions 24 Transposing Songs Tap on [More] in the toolbar, then on [Play Function] in the More screen that appears. Use [Transpose ] / [Transpose ] to transpose. [Transpose ] / [Transpose ] Adjusts the key in half steps, 24 half-steps lower or higher (i. e. 2 octaves in either direction). Chapter 5 Other Functions 25 Changing Song Tempo Tap on [More] in the toolbar, then on [Play Function] in the More screen that appears. Use the slider to adjust the tempo. [Tempo] Adjusts the tempo over the following range: Disklavier Mark IV: -50% to +20% Disklavier E3: -50% to +50% [Reset] Returns to the default tempo (0%). Chapter 5 Other Functions 26 Cancelling Parts Tap on [More] in the toolbar, then on [Play Function] in the More screen that appears. Use [Part Cancel] to switch parts on and off. [Part Cancel] Switches the left (L) or right (R) parts on and off. Chapter 5 Other Functions 27 Using Shortcuts Tap on [More] in the toolbar, then on [Short Cut] in the More screen that appears. Tap on the desired shortcut. Shortcut list* * Shortcuts can only be assigned, edited or deleted on the Disklavier. Chapter 5 Other Functions 28 6 Related Information Introduction 29 Notes on the Passcode Setting To prevent others from controlling your Disklavier with the Disklavier Controller, you can set the passcode on your Disklavier. Default setting No passcode is set as default, which means any Disklavier Controller can control your Disklavier. How to set the passcode The passcode can be set in the passcode setting screen of your Disklavier. For Disklavier Mark IV users: You can access this screen by tapping , then on . Refer on to the Advanced Operating Manual for more information. For Disklavier E3 and Disklavier Control Unit DKC-850 users: You can access this screen by pressing [SETUP] on the remote control, then selecting "Passcode. " Refer to the Operation Manual for more information. Set the 4-digit number as the passcode. You can control your Disklavier with the Disklavier Controller by entering the passcode set in this screen (see page 6). Delete or reset the passcode in the screen above. Chapter 6 Related Information 30 Troubleshooting If you have problems operating the Disklavier, see if any of the symptoms listed below apply to your problem and follow the recommended remedy. The Disklavier Controller does not function at all. [. . . ] Delete or reset the passcode in the screen above. Chapter 6 Related Information 30 Troubleshooting If you have problems operating the Disklavier, see if any of the symptoms listed below apply to your problem and follow the recommended remedy. The Disklavier Controller does not function at all. Your iPhone/iPod touch/iPad and the Disklavier may not be connected in a wireless environment. Make sure that your iPhone/iPod touch/iPad is connected to a WiFi access point that is on the same network as your Disklavier for this application to function. [. . . ]