User manual YAMAHA GW33

[. . . ] GUITAR PERFORMANCE EFFECTOR GUITAR PERFORMANCE EFFECTOR OWNER'S MANUAL SPECIAL MESSAGE SECTION (USA) This product utilizes batteries or an external power supply (adapter). DO NOTconnect this product to any power supply or adapter other than one described in the manual, on the name pIate, or specifically recommended by Yamaha. This Product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc. , is used, please observe all safety markings and instructions that accompany the accessory product. [. . . ] The on/off switching of the MOD 1/2 and Delay/Reverb blocks is determined by the On/Off parameter of those blocks. (See pages 24 and 27. ) 3 17 Effect programs can be edited in the Edit mode. Once you've edited a program, you can save it to a User memory location. (See SAVING EFFECT PROGRAMS on page 31. ) CAUTION!s Be careful not to press the p button at any time during editing. Doing so will call up the original effect program's settings and erase all settings you had made to that point. OPERATION 1 Select an effect program for editing and press the e button to enable the Edit mode. (The EDIT/COMPARE lamp lights and the ON/OFF lamp above Pedal Switch B flashes. ) Use Pedal Switches 1 ­ 5 to turn on the desired effect blocks. HINT s Since you'll probably want to listen to the changes as you make them, make sure that all relevant effect blocks are turned on. Better yet, turn off all blocks except the one you are editing. This lets you clearly hear only the effect you wish to edit. (One possible exception to this guideline is the Amp Simulator effect, changes to which are easier to hear when Distortion is also on. ) 2 COMP DIST / INSERT EQ / AMP MOD 1 -- -- --- --1~3 OD, DIST1, 2 (DI*+AN) 6~11 OD, DIST1, 2+INSERT 1 EQ / 2 STACK 4, 5 OD*+DIST1, 2 12 INSERT 4 TUBE PRE-DRIVE* 3 COMBO LOW / -- SPEED PITCH / PITCH L ENHANCE / SENSE TIME 1 CHORUS / 2 FLANGER 3 PHASER 4 PITCH SHIFT / 5 DETUNE MOD 2 DELAY REVERB N. GATE/UTIL TUNER/ METRONOME ······ · · · · · · · · · · ······ · · · · · · · · · ······ 6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH -- -- --- --1 HALL -- -- --- --TUNING PITCH (0~5 = 440~445Hz) A 2 ROOM 3 STAGE 4 PLATE THRESHOLD YES · PARAM ······················· · · · · CHECK COPY / SWAP / WRITE ················································· MEMORY NO. NO Use these to select the desired block for editing. (In this example, EQ/AMP is selected. ) Selects the type of effect. (In this example, 1 EQ is selected. ) Adjusts the LOW parameter for the EQ effect. (The dash indicates that no parameter is available for the other effects. ) 18 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 ATTACK TIME -- B 3 Use the y and n buttons to select the desired effect block row (in the parameter matrix printed on the panel). (The lamp at the left of the corresponding block lights. ) NOTE s The TUNER/METRONOME row cannot be selected in the Edit mode. 4 Use the Parameter Dials to adjust the effect parameters. Parameter Dial A is used to change the effect type of the selected block; B ­ E are used to change the corresponding parameters. In the example shown below, the EQ/AMP block has been selected. SENSE -- LEVEL DRIVE TONE LEVEL MID / -- DEPTH -- / PITCH R FREQUENCY FB TONE VOLUME POSITION BEAT (14~88 = 1/4~8/8) C HIGH / TONE TONE / FB LEVEL ON/OFF MIX (SWITCH 4) MIX / RANGE MIX MIX MINIMUM VOLUME TEMPO (60~86. =60~186) D ON/OFF (SWITCH 5) TOTAL LEVEL CLICK LEVEL (1 LO 2 MID 3 HI) E Adjusts the MID parameter for the EQ effect. (The dash indicates that no parameter is available for the other effects. ) Adjusts the LEVEL parameter. Adjusts the HIGH parameter for the EQ effect and the TONE parameter for the others. HINT 1 s When editing an effect, make sure that the Level or Mix parameters of the effect are set to relatively high values before adjusting any other parameters. Doing this ensures that any changes you make with the other Parameter Dials will be fairly noticeable. For information about each of the effects and their parameters, refer to the section EFFECTS AND PARAMETERS on page 20. s Compare Mode While editing an effect program, you can compare the sound of the newly edited program with the original one. To do this, press the e button (during editing). (The EDIT/COMPARE lamp flashes to indicate the Compare mode is active. ) EDIT/ COMPARE EDIT/ COMPARE Each press of the e button switches back and forth between the original program (lamp flashes) and your new edits (lamp lights continuously). While the EDIT/COMPARE lamp is flashing (Compare mode), you can hear the sound of the original effect program. You can also view the original parameter values: simply select the desired effect block with the y and n buttons and turn the Parameter Dials. [. . . ] 5 parameter values checking in the Play mode . 4 R restoring factory-set effect programs . 5, 13, 19 FCC INFORMATION (U. S. A) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! [. . . ]