User manual YAMAHA HTR-6280

[. . . ] U HTR-6280 AV Receiver OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 10 11 12 Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 13 14 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] Video Out Input source: AUDIO 1/2, MULTI CH Choices: AV1 to AV6, V-AUX, Off* 2 3 Specifies a video signal to be output during an audio reproduction. For details, see "Selecting a video signal to be output during an audio reproduction" on this page. Video;;;;;;Off 4 Press jCursor l / h to select a video input jack to be used during an audio reproduction. ­ AV1-2 (COMPONENT VIDEO) ­ AV3-6 (VIDEO) ­ V-AUX (VIDEO) ­ Off (no video output) To exit the Option menu, press rOPTION. 5 50 En Editing surround decoders/sound field programs Setting sound field parameters Although the field sound programs would satisfy you as they are with the default parameters, you can arrange sound effect or decoders suitable for acoustical conditions of sources or rooms by setting the parameters. y · You cannot configure the parameters when "Memory Guard" is set to "On" (page 61). Sound field parameters y · The default settings are marked with "*". INTRODUCTION CINEMA DSP basic parameters DSP Level Adjustable range: ­6dB to 0dB* to +3dB 1 2 3 4 Turn on the video monitor connected to this unit. The GUI screen appears on the video monitor. Press jCursor n to select "Setup" and then press jENTER. Press jCursor k / n to select "DSP Parameter" and then press jENTER. Sound field program Fine adjusts an effect level (level of the sound field effect to be added). You can adjust the level of the sound field effect while checking sound levels. Adjust "DSP Level" as follows. · There are no differences between effects of the sound field programs. · The sound field effect is added too much. Dialogue Lift Choices: 0* to 5 PREPARATION BASIC OPERATION DSP Parameter Program Name Decode Type DSP Level P. Room Size Sci-Fi PLIIx Movie 0dB 16ms 1. 0 2ms 1. 0 Use this feature to adjust the vertical position of the dialogues in movies. The ideal position of the dialogues is at the center of the video monitor screen. ADVANCED OPERATION Sound field parameters Set values The ideal dialogue position 5 Press jCursor k / n to select "Program Name" and then press jCursor l / h to select a sound field program to edit. Press jCursor k / n to select a parameter to edit and then press jCursor l / h to change the setting. For details on functions and adjustable ranges of the sound field parameters, see "Sound field parameters" on this page. y · Repeat steps 5 and 6 to change other sound field program parameters. ADDITIONAL INFORMATION 6 If the dialogues are heard at the lower position of the video monitor screen, increase the value of "Dialogue Lift". Move up to the ideal dialogue position APPENDIX 7 To turn off the GUI screen, press iON SCREEN. When the value is set to zero, the position is at the lowest. The position gets higher as you increase the value. Notes · This setting is available only when "Extra Speaker Assignment" is set to "Presence" (page 57). · You cannot move the dialogue position down from the initial dialogue position. To initialize the parameters of the selected sound field program, press jCursor n repeatedly to select "Initialize" and then press jCursor h. Then, press jCursor h again to execute the initialization or jCursor l to cancel it. 3D DSP Choices: On*, Off English When CINEMA DSP 3D is enabled, sets whether to use sound field programs in 3D mode. 51 En Editing surround decoders/sound field programs Note · This setting is available only when "Extra Speaker Assignment" is set to "Presence" (page 57). Level Level Source sound Early Sound field parameters for advanced configurations Parameters for adjusting early-reflected sound Time Sound source Time Initial Delay / P. Back Initial Delay Adjustable range: 1 to 99ms (Initial Delay / P. [. . . ] 34 XM Satellite Radio, troubleshooting . . . . . . . . . . . . . 71 Y YPAO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 YPAO, troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Z ZONE2 CONTROL, front panel . . . . . . . . . . . . . . . . . . . . . [. . . ]