User manual YAMAHA IF2108

[. . . ] - Mount only one speaker on each speaker stand. - Use the speaker stands with their legs fully opened. - Use the stand at a height of less than 140cm. - Add weight such as sand bags around the stand legs to prevent them from falling over. [. . . ] - Make sure to use the specified hardware. - Inspect the device periodically. · Before moving the device, remove all connected cables. · Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. · Do not place the device in an unstable position where it might accidentally fall over. · When turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid speaker damage. When turning the power off, the power amplifier should be turned off FIRST for the same reason. · Do not operate this device at high volume levels or at a level that is uncomfortable, since it is capable of producing sound levels that could cause permanent hearing loss. If you experience any discomfort or ringing in the ears, or suspect an hearing loss, you should consult an audiologist. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. * Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation. * Company names and product names herein are trademarks or registered trademarks of their respective companies. For details on signal processor settings when driving speakers with the use of multiple power amplifiers, please refer to the web site below. Yamaha Pro Audio global web site http://www. yamahaproaudio. com/ (6)-1 Neutrik Speakon NL4 plug wiring Connect the plugs as shown below. Eye bolt strength Keep in mind that the strength of the eye bolt differs depending on the suspension angle of the speaker. Make sure that the load for each eye bolt is less than 740 kg when suspending at an angle of 0 degrees, and less than 185 kg at an angle of 45 degrees. CAUTION Be sure to use proper speaker cable-not shielded instrument or line cable-for all speaker connections. CAUTION When using the eye bolts, make sure that the suspension angle is within the range of 0 to 45 degrees, as shown below. 0º (740kg) 45º (185kg) 90º (148kg) 1- 1+ 2+ 2- CAUTION NEUTRIK plug 1+ 1­ 2+ 2­ NOTE Passive + ­ Do not suspend the eye bolts as shown in the diagram below. Rotatable horn 1. Remove all fixing screws on the grille, and remove the 2. grille from the speaker. Remove all screws installed on the horn, pull out the horn from the speaker, rotate the horn 90 degrees, and re-install the horn to the speaker. The Speakon jack and barrier strip terminals are connected in parallel. Suspended Installation CAUTION The strength of the suspension points on the speaker is 60 CAUTION kg Be careful when rotating the horn so that you do not accidentally cut the connection wires connected to the horn driver. per point (maximum). Before When doing any installation or construction work, consult with an installation expert. choosing the installation location, suspension wire and mounting hardware, make sure all are strong enough to support the weight of the speaker. Rotate 90 degrees Some fittings may deteriorate over extended periods of time due to wear and or corrosion. For optimum safety, the installation should be checked thoroughly at regular intervals. Vertical Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or improper installation. Horizontal Using eye bolts for suspension For optimum safety, make sure to carefully follow the precautions below. CAUTION Use Use Use only the supplied eye bolts. three or more eye bolts for suspended installations. Vertical the optional array frame if you intend to suspend a speaker from another suspended speaker. Install the eye bolts to multiple surfaces of the speaker, not just one surface. Horizontal IF2108/2208 Owner's Manual English 3 Specifications System Type Model Specifications/Drive Mode Frequency Range (-10dB) (4)*1 Frequency Range (±3dB) (4)*1 Nominal Coverage (H x V, -6dB) Power Rating Nominal Impedance Sensitivity (1W@1m) Calculated Peak SPL Calculated Continuous SPL 55 Hz ­ 19k Hz 75 Hz ­ 18k Hz 90º x 60º, can be rotated to 60º x 90º 200 W*2 8 ohms 95dB SPL 124dB SPL 118dB SPL 2-way full-range speaker IF2208(W) Passive 55 Hz ­ 19k Hz 75 Hz ­ 18k Hz 2-way full-range speaker IF2108(W) Passive 90º x 60º, can be rotated to 60º x 90º 100 W*2 8 ohms 95dB SPL 121dB SPL 115dB SPL Components LF HF 2 x 8" (20cm) Woofer, 2" (50mm) Voice Coil Rotatable Constant Directivity Horn, 1" (25mm) exit, 1. 7" (44mm) Voice Coil Compression Driver 8" (20cm) Woofer, 2" (50mm) Voice Coil Rotatable Constant Directivity Horn, 1" (25mm) exit, 1. 7" (44mm) Voice Coil Compression Driver Enclosure Dimensions (H x W x D) Weight Shape Material Finish Grill Connectors Flying Hardware Pole Mounts Handle 673 x 283 x 250 mm (26. 5 x 11. 1 x 9. 8 in) 19 kg (42 lbs) Multi-angle wedge 5/8 inch (16mm), 11-ply Finnish Birch Textured Black (Textured White) 16 gauge powder coated perforated steel grilles, backed with acoustically transparent reticulated foam 2x Neutrik NL4 and barrier strip, wired in parallel 11x M10 for shoulder eyebolts and U-bracket 6x M8 for 3rd party speaker mount hardware One One 448 x 283 x 250 mm (17. 6 x 11. 1 x 9. 8 in) 14 kg (31 lbs) Multi-angle wedge 5/8 inch (16mm), 11-ply Finnish Birch Textured Black (Textured White) 16 gauge powder coated perforated steel grilles, backed with acoustically transparent reticulated foam 2x Neutrik NL4 and barrier strip, wired in parallel 11x M10 for shoulder eyebolts and U-bracket 6x M8 for 3rd party speaker mount hardware One One Optional Accessory U-bracket Array Frame UB2208(W) n/a UB2108(W) n/a 3rd party accessory Omnimount (US) Multimount (US, Allen products) Powermount (UK) Ohashi (Japan) * 1: With recommended YAMAHA DSP configuration. IEC noise. 60. 0 series 020, 022 series 100 series SPH-140, SPA-140, BCH-140 series 60. 0 series 020, 022 series 100 series SPH-140, SPA-140, BCH-140 series * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. [. . . ] * 14 IF2208/IF2108 Dimensions IF2108 86. 8 102. 1 132. 3 168. 6 75 ° 6-M10 283 41. 3 127 365. 1 2-M8 M10 127 448 85 72 31 165 178 219 250 15 ° 75 0° 41. 3 6. 313 223. 8 113 41. 3 139 4-M8 4-M10 365. 1 69. 9 66. 9 51. 1 41. 3 111 127 66. 9 unit: mm IF2208 87 102 168. 6 132 66. 9 283 112. 5 5. 000 85 72 31 6-M10 165 178 219 250 4-M10 2-M8 127 673 M10 273 139 69. 9 50. 8 111 127 336. 5 unit: mm IF2108/IF2208 15 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S. A. [. . . ]