User manual YAMAHA INVERTER EF1000IS

[. . . ] Generator OWNER'S MANUAL EF1000iS LIT-19626-01-19 7CG-28199-10 AE00002 INTRODUCTION Congratulations on your purchase of your new Yamaha. This manual will provide you with a good basic understanding of the operation and maintenance of this machine. If you have any questions regarding the operation or maintenance of your machine, please consult a Yamaha dealer. CODE AE00012 SERIAL No. IDENTIFICATION NUMBER RECORDS Record your Primary I. D. , and serial numbers in the spaces provided, to assist you in ordering spare parts from a Yamaha dealer. [. . . ] NOTE: Grasp the carrying handle firmly to prevent the generator from falling over when pulling the recoil starter. 704-017 6. After the engine starts, warm up the engine until the engine does not stop when the choke knob is returned to the original position. 7. Push the choke knob back to the original position. 701-049c NOTE: When starting the engine, with the economy control switch "I" (ON), and there is no load on the generator: 9 in ambient temperature below 3°C (37°F), the engine will run at the rated r/min (5, 000 r/min) for 5 minutes to warm up the engine. 9 in ambient temperature above 3°C (37°F), the engine will run at the 4, 000 r/min for 3 minutes to warm up the engine. The economy control unit operates normally after the above time period, while the economy control switch is "I" (ON). ­ 13 ­ AE01000 APPLICATION RANGE AC DC Power factor 1 0. 8­0. 95 0. 4­0. 75 (Efficiency 0. 85) Rated voltage 12V Rated current 8A EF1000iS ­900W ­720W ­300W q NOTE: 9 "­" means below. 9 Application wattage indicates when each device is used by itself. 9 The simultaneous usage of AC and DC power is possible but total wattage should not exceed the rated output. EX: Generator rated output Frequency Power factor 1. 0 AC 0. 8 763-225 900VA ­800W ­640W 96W (12V/8A) DC -- 9 The overload indicator light 1 comes on when total wattage exceeds the application range. (See page 16 for more details. ) cC Be sure the total load is within generator rated output otherwise generator damage will occur. NOTE: Some precision equipment is voltage sensitive and may require a more uniform voltage supply than portable generators provide. Examples include some medical equipment, personal computers, and some inverters that sense peak and RMS voltage values. Consult the precision-equipment vendor before relying on any portable generator to provide power to such equipment. ­ 14 ­ AE01023 CONNECTION Alternating Current (AC) cC 9 Be sure all electric devices including the lines and plug connections are in good condition before connection to the generator. 9 Be sure any electric devices are turned off before plugging it in. 9 Be sure the total load is within generator rated output. 9 Be sure the receptacle load current is within receptacle rated current. Wind the power lead 2 or 3 turns around handle. Plug in to the AC receptacle. 761-079 761-078a q 4. Make sure the AC pilot light is on. 1 AC pilot light 763-226 5. Turn the economy control switch (Black) to the " I " (ON) position and turn on any electric devices. q 1 " I " (ON) 763-222a NOTE: The economy control switch must be turned to "3" (OFF) when using electric devices that require a large starting current, such as a compressor or a submergible pump. ­ 15 ­ q AE00953 763-225 Overload indicator light The overload indicator light 1 comes on when an overload of a connected electrical device is detected, the inverter control unit overheats, or the AC output voltage rises. The electronic breaker will then activate, stopping power generation in order to protect the generator and any connected electric devices. The AC pilot light (green) will go off and the overload indicator light (red) will stay on, but the engine will not stop running. When the overload indicator light comes on and power generation stops, proceed as follows: 1. [. . . ] 9 To prevent ELECTRIC SHOCK do not hold spark plug lead with hand while testing. J Engine starts. L Incorrect Replace or Adjust Gap. M OK Clean the spark plug. N Check the following O Clogged 9 Fuel line clogging 9 Air cleaner element P OK clogging. ­ 29 ­ Q Clean or Replace; Consult Yamaha dealer. Consult a Yamaha dealer. a R AE00601 STORAGE Long term storage of your machine will require some preventive procedures to guard against deterioration. AE01095 706-025 DRAIN THE FUEL 1. [. . . ]