User manual YAMAHA K-600

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Automatically selects the most suitable decoder for input signals whether or not the flag for reproducing surround back channel is present, and always reproduces signals in 6. 1channel. Always reproduces signals in 5. 1-channel whether or not the flag for reproducing surround back channel is present. PLIIx Movie Sampling Bitrate Notes PLIIx Music · "No Signal" is displayed when no signals are input and "---" is displayed when signals that this unit cannot recognize are input. · The bit rate may vary during playback. Video information Information Description Format and resolution of video input signal. Format and resolution of video output signal. Error messages about HDMI signals and HDMI components. See the following for details of the error messages. EX/ES In Out Message Off HDMI error message (appears only when an error has occurred) HDCP authentication failed. HDCP Error Device Over The number of HDMI components connected is Out of Res. over the limit. The connected monitor is not compatible with the video input signal. FM Mode Input source: TUNER Choices: Stereo*/Mono Sets FM broadcasting receiving mode. You can get a better reception in MONO mode. 44 En Setting the option menu for each input source (OPTION menu) Auto Preset Input source: TUNER Automatically detects radio stations in the FM frequency band and registers them as preset stations (see page 29). Clear Preset Outputting a video signal input from another input source during reproducing a multi-channel audio signal When "MULTI" is selected as the input source, a video signal input from another terminal can be output to the video monitor. For example, even if an audio and video component such as a DVD player that does not support a multi-channel digital audio output, the video signal can be output to the video monitor while reproducing a multichannel analog audio signal. INTRODUCTION Input source: TUNER, XM, SIRIUS When TUNER is selected:See page 30. You can adjust the level of the sound field effect while checking sound levels. Adjust "DSP Level" as follows. · There are no differences between effects of the sound field programs. · The sound field effect is added too much. Reduce the effect level. Sound field parameters 4 Press oCursor k / n to move "" to the sound field program and press oCursor l / h to select the sound field program. 46 En p [ Set values Editing surround decoders/sound field programs Dialog Lift Choices: 0* to 5 Use this feature to adjust the vertical position of the dialogues in movies. The ideal position of the dialogues is at the center of the video monitor screen. The ideal dialogue position Adjusts attenuation characteristics of early-reflected sound. You can create a lively sound field (with a high reverberant sound level) as you increase the value, and a dead sound field (with a low reverberant sound level) as you decrease the value. Creating either a lively sound field or a dead sound field in an actual music hall is determined by the acoustic absorption characteristics of reflection surfaces. A dead sound field is created when the attenuation time is short while a lively sound field is created when the attenuation time is long. Original source sound INTRODUCTION PREPARATION Level Time Delay Sound source Delay Level If the dialogues are heard at the lower position of the video monitor screen, increase the value of "Dialog Lift. " Early-reflected sound Time BASIC OPERATION Move up to the ideal dialogue position Reflecting When the value is set to zero, the position is at the lowest. The position gets higher as you increase the value. Small = 1ms Large = 99ms Notes · "Dialog Lift" is displayed only when the presence speakers are available. · You cannot the move the dialogue position loser than the default setting. y · We recommended that you adjust the size of corresponding sound field when you adjust the delay time. ADVANCED OPERATION Sound field parameters for the advanced configurations Parameter for CINEMA DSP 3D On* / Off Parameters for specifying room size Parameter Adjustable range 0. 1 to 2. 0 3D DSP Choices: When CINEMA DSP 3D is enabled, sets whether to use sound field programs in 3D mode. [. . . ] 7 Tuner, troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Tuning, AM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Tuning, FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 TUNING/CH l / h, front panel . . . . . . . . . . . . . . . . . . . . [. . . ]