User manual YAMAHA L-140-L-140S-L-70-L-70S ASSEMBLY INSTRUCTIONS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual YAMAHA L-140-L-140S-L-70-L-70S. We hope that this YAMAHA L-140-L-140S-L-70-L-70S user guide will be useful to you.
Lastmanuals help download the user guide YAMAHA L-140-L-140S-L-70-L-70S.
Manual abstract: user guide YAMAHA L-140-L-140S-L-70-L-70SASSEMBLY INSTRUCTIONS
Detailed instructions for use are in the User's Guide.
[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] MIDI: The MIDI connector is the currently active MIDI port. USB-1, USB-2: The corresponding USB port is selected for MIDI input. Slot1 [Slot1 ~ Slot4 (DME64N)]: A card installed in the corresponding I/O slot is currently selected for MIDI input. Edit using the "List Parameters" editing procedure described on page 38. NOTE
When the DME64N/24N is functioning as the device group master and is connected to a computer running the DME Designer application via USB, the MIDI port being used by the DME Designer will not be available.
Ext HA Ctrl (External head amp control)
Displays/sets the type of connection to be used for external head amp control. OFF: Select "OFF" when this function is not to be used. Remote (422): Allows remote head amp control. Always use this setting when a remote head amp unit (AD8HR, AD824) is connected. Also, don't change the setting while a remote head amp is connected. Doing so can damage the unit.
COM
Displays/sets the type of connection to be used for DME protocol communication. Normally, set this to "OFF".
DME64N/DME24N Owner's Manual
49
Panel Operation and Displays
Utility Displays
Protocol (MIDI Protocol Setup)
Displays/sets the protocol to be used for communication with devices connected via MIDI. Some cards can also be reset via this page. To reset the calibration, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to reset all inputs, or select an individual input from 1 to 16 to be reset, then press the [ENTER] button.
MAX
Sets the maximum calibration value. To set the MAX value, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MAX value to the current input voltage.
MIN
NOTE
This page will not appear on the ICP1 display.
Card Name
The name of the installed card appears here.
Sets the minimum calibration value. To set the MIN value, use the [ E ] [ ] [ ] [ F ] buttons to select ALL to set all inputs, or select an individual input from 1 to 16 to be set, then press the [ENTER] button to set the MIN value to the current input voltage.
Reset
Resets the installed card.
Calibration Info
Shows the calibration settings as well as the current input voltage.
Format
Displays the 88. 2/96 kHz audio signal transfer mode. The input setting is on the left and the output setting is on the right. No Display (Default): 44. 1/48 kHz audio signal transfer. SP (Double Speed): An 88. 2/96 kHz capable card is installed, allowing direct transfer at 88. 2 or 96 kHz. CH (Double Channel): A 44. 1/48 kHz card is installed, and 88. 2 or 96 kHz audio is transferred by using two 44. 1/48 kHz channels to transfer each channel of 88. 2/96 kHz audio. The number of audio channels that can be handled in this mode is half the number of channels normally handled by the card.
DME64N/DME24N Owner's Manual
51
Panel Operation and Displays
Utility Displays
Head Amplifier Setup (HA) Page
Provides access to the head amplifier settings. Refer to "REMOTE Connection" on page 28 for head amplifier control signal connection. NOTE
This page will not appear on the ICP1 display.
WCLK (AD8HR/AD824 only)
Specifies the word clock signal to be used by the head amplifier(s). [. . . ] 32
Z
zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DME64N/24N Owner's Manual
75
MEMO
76
DME64N/24N Owner's Manual
MEMO
DME64N/24N Owner's Manual
77
MEMO
78
DME64N/24N Owner's Manual
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA L-140-L-140S-L-70-L-70S
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA L-140-L-140S-L-70-L-70S will begin.
