User manual YAMAHA LG50

[. . . ] The result is better mixes in less time: a huge advantage during high-pressure pre-show setup. StageMix does not provide remote control of all LG50 parameters, but is focused on the requirements for adjusting monitor mixes on stage. Yamaha Commercial Audio LG50 StageMix V1. 6 User Guide CONTENTS Page 1. 0 2. 0 3. 0 3. 1 3. 2 3. 3 3. 3. 1 3. 3. 2 3. 3. 3 4. 0 4. 1 4. 1. 1 4. 1. 2 4. 1. 3 4. 1. 4 4. 1. 5 4. 1. 6 4. 2 4. 2. 1 4. 2. 2 4. 2. 3 4. 2. 4 4. 2. 5 4. 3 4. 4 4. 4. 1 4. 5 4. 6 4. 6. 1 4. 6. 2 4. 6. 3 4. 6. 4 4. 7 4. 7. 1 4. 7. 2 4. 7. 3 4. 7. 4 4. 7. 5 4. 7. 6 4. 7. 7 4. 7. 8 System Requirements Wi-Fi Settings Getting Started LG50 Network Setup iPad Wi-Fi Settings StageMix Setup OFFLINE DEMO Mode Configure StageMix to Work with an LG50 Select a Mixer and Begin Working StageMix Operation Mixer Window Channel Bank Navigation Channel Names Faders Channel ON CUE Master Bank SETUP Fader Delay Filled EQ Graph Set EQ band to 0dB with Double-Tap Channel Select ­ StageMix Follows Console Channel Select ­ Console Follows StageMix Long Faders SENDS ON FADERS Mix Sends ON EQ Editing Parametric EQ Editing Screen HPF EQ Bands 1 & 4 EQ ON EQ FLAT, EQ DEFAULT Graphic EQ Editing Screen Navigation in the GEQ Overview Section Rack Position GEQ Type Editing GEQ Bands Navigation in the GEQ Editing Section GEQ ON GEQ FLAT Copy/Paste 4 4 5 5 5 6 7 7 8 9 9 9 10 10 10 11 11 12 12 12 12 12 12 13 14 15 16 17 18 19 19 19 20 20 20 21 21 21 21 21 21 Page 2 Yamaha Commercial Audio 5. 0 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 Troubleshooting No Wi-Fi Available Connection Error Connection Lost Graphic EQ Doesn't Affect the Sound Problems Moving Multiple Faders Incompatibility with Earlier LG50 Versions LG50 StageMix V1. 6 User Guide 22 22 22 23 23 24 24 Special Notices · The software and this Owner's Manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] Using the iPad's multi-touch facility, up to eight faders can be moved simultaneously. Note: "Multitasking Gestures" must be turned Off in the iPad in order to allow four or more faders to be adjusted simultaneously. 4. 1. 4 Channel ON Press [ON] to change the on/off status of the channel. The button is green when the channel is on. When a channel is off, its name and level meter will go dim, and its fader position shown in the "Navigation/Meter Bridge" will also go dim. Page 10 Yamaha Commercial Audio LG50 StageMix V1. 6 User Guide 4. 1. 5 CUE The [CUE] buttons for each channel control the mixer's cue functions. Their operation mode corresponds to the status of the [LAST CUE] button on the left side of the Mixer Overview. When the [LAST CUE] button is highlighted yellow, only one channel can be cued at a time. When this button is grey, multiple channels can be cued simultaneously. This is equivalent to Mix Cue mode in the LG50 console. The [CUE CLEAR] button will cancel any cues that have been activated. This is useful when there are multiple cues to cancel, and when some are hidden in other layers. 4. 1. 6 Master Bank Pressing the [Master] block in the "Navigation/Meter Bridge" will cause channels from the master section to appear in the fader strips. When a Mix, Matrix or Master block is selected in the "Navigation/Meter Bridge", the [SENDS ON FADERS] button is not available. To exit "SENDS ON FADERS" mode, press the [SENDS ON FADERS] button in the left column. Page 15 Yamaha Commercial Audio 4. 5 LG50 StageMix V1. 6 User Guide EQ Editing Every channel in the LG50 has a dedicated Parametric EQ (PEQ). The LG50 also has Graphic EQs (GEQs) that can be assigned (inserted) on input or output channels. Note: assignment of GEQs to channels must be done on the console and cannot be done in StageMix. At the bottom-left, there are "previous" and "next" arrow buttons for navigating to different channels. Note: the In/Out meters display the levels going In and Out of the EQ section. One band of Parametric EQ can be adjusted at a time. Press one of the green circles to select the band, and it will be highlighted yellow. EQ bands in StageMix are labelled as follows: HP = HPF (input channels only) 1 = Low Band 2 = Low-Mid Band 3 = High-Mid Band 4 = High Band The current values for Freq, Gain and Q will be displayed for the currently selected EQ band. Page 17 Yamaha Commercial Audio LG50 StageMix V1. 6 User Guide Gain and Frequency can be adjusted by dragging the circle around the graph. Q is adjusted by using the iPad's "pinch" gesture: hold one finger (or thumb) on the screen while moving another finger closer to or further away from the first. [. . . ] Note: sliders will become transparent and cannot be operated when there are no remaining bands available for a Flex 15 GEQ. 4. 7. 5 Navigation in the GEQ Editing Section In addition to navigation in the upper GEQ Overview section, swipe gestures can be used to navigate through the GEQ bands in the lower editing section. 4. 7. 6 GEQ ON The [GEQ ON] button in the upper-right part of this screen turns the GEQ On or Off. The button appears blue when GEQ is On and turns grey when GEQ is Off. [. . . ]