User manual YAMAHA LG80

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] In addition, you can use the WITH MIX SEND button to enable Recall Safe for the on/off status and send level of the signals sent from input channels to MIX buses. If you want all parameters shown in the lower part of the field to be subject to Recall Safe, turn on the ALL button (this is the default setting). LS9-32 13 Scene memory These buttons correspond to the following parameters. Button name ALL HA EQ DYNA 1 DYNA 2 MIX ON MIX SEND FADER CH ON Corresponding parameters All parameters Head amp settings (including external HA) EQ settings (including ATT/HPF) Dynamics 1 settings Dynamics 2 settings On/off status of signals sent to MIX buses Send levels of signals sent to MIX buses Fader positions On/off status of [ON] keys NOTE · If you turn on the ALL button, all other buttons of the SAFE PARAMETER field will be turned off. LG80/32 Owner's Manual 141 Using the Recall Safe function These buttons correspond to the following parameters. Button name ALL EQ DYNA 1 MTRX ON MTRX SEND FADER CH ON WITH MIX SEND Corresponding parameters All parameters (except for WITH MIX SEND) EQ settings (including ATT) Dynamics 1 settings On/off status of signals sent to MATRIX buses Send levels of signals sent to MATRIX buses Fader positions On/off status of [ON] keys On/off status and send level of signals sent from input channels to MIX buses 4 To enable Recall Safe for the selected channel, turn on the SAFE button in the SAFE PARAMETER field. Channels for which Recall Safe is enabled will be highlighted in the CH RECALL SAFE field. SAFE button NOTE · If the ALL button is on, all buttons will be turned off except for the WITH MIX SEND button located in the lower part of the SAFE PARAMETER field. · You can switch the WITH MIX SEND button on/off while the ALL button is left on. If a MATRIX channel is selected With the exception of the types of button that are displayed, this is the same as for a MIX channel. In addition, you can use the WITH MATRIX SEND button to enable Recall Safe for the on/off status and send level of the signals sent from output channels to MATRIX buses. LG80 SAFE button LS9-32 NOTE These buttons correspond to the following parameters. Button name ALL EQ DYNA 1 FADER CH ON WITH MATRIX SEND Corresponding parameters All parameters (except for WITH MATRIX SEND) EQ settings (including ATT) Dynamics 1 settings Fader positions On/off status of [ON] keys On/off status and send level of signals sent from MIX channels / STEREO/MONO channels to MATRIX buses · Simply selecting a parameter in step 3 does not enable Recall Safe. To turn Recall Safe on/off, you must also perform the operation of step 4. HINT · In the CH RECALL SAFE field, the color of the highlight will be green if the ALL button was selected in step 3, or blue if buttons other than ALL were selected. · If you press the CLEAR ALL button, Recall Safe will be defeated for all channels for which it is enabled (i. e. , the highlighted channels). · You can also switch Recall Safe on/off in the SELECTED CH VIEW screen's SAFE field ( p. 88). NOTE · If you turn on the ALL button, all buttons will be turned off except for the WITH MATRIX SEND button located in the SAFE PARAMETER field. · You can switch the WITH MATRIX SEND button on/off while the ALL button is left on. 142 LG80/32 Owner's Manual Using the Recall Safe function · Using the Fade function 5 If you want to enable Recall Safe for global parameters, turn on the desired buttons in the GLOBAL field. These buttons correspond to the following parameters. Button name INPUT PATCH INPUT NAME OUTPUT PATCH OUTPUT NAME 1­8 Corresponding parameters Input port patching Input channel name Output port patching Output channel name Rack 1­8 settings 6 When you've finished making settings, execute a Recall operation. Only the selected channel(s) and parameter(s) will be excluded from Recall operations. 124) and the MIX/MATRIX bus settings in the SYSTEM SETUP screen ( p. 213) are not subject to Recall Safe; the settings of the recalled scene will always be reproduced. When you've finished making settings, move the cursor to the OK button and press the [ENTER] key to close the FADE TIME popup window. HINT · The fade time you specify here is used for all channels selected in step 4. 144 LG80/32 Owner's Manual Chapter 14 Monitor/Cue This chapter explains the LS9's monitor/cue functions. About the monitor/cue functions The Monitor function lets you audition various signals through your nearfield monitors or headphones. The LS9's front panel has a PHONES OUT jack for monitoring, and this jack always lets you monitor the signal that is selected as the monitoring source. By assigning the MONITOR OUT L/R/C channels to the desired output jacks, you can also monitor the same signal through external speakers. You can select the following signals as the monitor source. · · · · · STEREO channel output signal MONO channel output signal STEREO + MONO channel output signal 2TR IN DIGITAL jack input signal INPUT channels 15/16 {31/32} input signal · USB memory recorder output signal · Any combination of up to eight signals from the STEREO, MONO, MIX, and MATRIX channels, the USB memory recorder output signal, INPUT channel 15/ 16 {31/32}, and the 2TR IN DIGITAL jack input signal The Cue function lets you check an individual selected channel by temporarily sending it from the output jacks assigned to the MONITOR OUT channel or from the PHONES OUT jack. When you press the top panel [CUE] key, the cue signal of the corresponding channel is sent as the monitor output from the selected output port. NOTE · The cue signal is sent to the same output destination as the monitor signal. Be aware that for this reason, the cue signal will no longer be sent to the connected monitor speakers if you turn off the Monitor output. However, the cue signal will always be sent to the PHONES OUT jack. CUE LR CUE TRIM (INPUT/OUTPUT/DCA) PHONES OUT LR MONO METER CUE L METER CUE R CUE LOGIC 2 DA Tip Ring Sleeve PHONES LEVEL [PHONES] CUE L CUE R PHONES LEVEL LINK PHONES L PHONES R To PHONES OUT To PHONES OUT 2TRD L, R INPUT 15, 16{31, 32} PLAYBACK OUT MONITOR SELECT 2TRD L, R INPUT 15, 16{31, 32} PLAYBACK OUT MONITOR R MONITOR MONO(C) METER MONITOR R METER MONITOR MONO(C) DIMMER STEREO OUT L, R STEREO OUT MONO(C) STEREO OUT L, C, R MONITOR L MONO METER MONITOR L MONITOR OUT L MONITOR OUT R MONITOR OUT MONO(C) To OUTPUT PATCH To OUTPUT PATCH To OUTPUT PATCH STEREO OUT L, R STEREO OUT MONO(C) MIX OUT1-16 MATRIX OUT1-8 DEFINE MIX (MAX:8ch) ON TALKBACK ON MONITOR DIMM ON +MONO(C) MONITOR LEVEL MONITOR SELECT MONITOR LEVEL Selects the monitor source. METER Detects and indicates the level of the monitor signal or cue signal. DIMMER Adjusts the level of the monitor/cue signal. This affects the output jacks that are assigned to the MONITOR OUT L/R/C channels, and also the PHONES OUT jack. ON (On/off) Turns the monitor output on/off. PHONES LEVEL (Headphone level) Attenuates the monitor/cue signal by a fixed amount. Adjusts the output level of only the PHONES OUT jack. LG80/32 Owner's Manual 145 Monitor/Cue The following diagram shows the monitor/cue signal flow. 14 Using the Monitor function Using the Monitor function This section explains how to select the desired monitor source, and monitor it from the PHONES OUT jack or external monitor speakers. 1 Connect your monitor system to the rear panel OMNI OUT jacks, 2TR OUT DIGITAL jack, or an I/O card installed in a slot. The monitor signal can be sent to any desired output jack or output channel. If you're monitoring through headphones, make sure that your headphones are connected to the front panel PHONES OUT jack. E MONITOR LEVEL knob Adjusts the output level of the monitor signal. F DIMMER field The Dimmer function which temporarily attenuates the monitor signal can be switched on/off here. Use the knob in this field to adjust the amount of attenuation. [. . . ] Input [-42dBu] OMNI OUT1-16/8 [Default setting] 2 Nominal Input [-62dBu] -70 1 INPUT 1-32/16 (GAIN MIN. ) 2 INPUT 1-32/16 (GAIN MAX. ) -80 -90 -100 -110 -120 -130 -140 -150 -160 Max. DSP Noise Floor -170 -180 -190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]