User manual YAMAHA LS9-16/LS9-32 ANNEXE 8

[. . . ] LS9 StageMix V4. 0 User Guide Welcome: Thank you for downloading the “LS9 StageMix” iPad app for the Yamaha LS9 digital mixing consoles. The latest firmware version for LS9 can be downloaded from www. yamahaproaudio. com StageMix is an application for the Apple iPad that provides remote control of Yamaha LS9 digital mixing console functions via a simple, intuitive graphical interface from anywhere within wireless range. The software has been specifically designed to allow engineers to adjust monitor mixes from the performers’ positions on stage, directly controlling mix parameters via the iPad rather than having to rely on verbal directions to a second engineer. The result is better mixes in less time; a huge advantage during high-pressure pre-show setup. [. . . ] If a GEQ curve is currently displayed, swiping from left to right will cause the PEQ curve to be displayed. 5. 1. 3 Accessing the EQ Editing Screens To access PEQ or GEQ editing, tap on the EQ curve to open the appropriate EQ Editing Screen. • • If a PEQ curve is displayed, the PEQ editing screen will be accessed. If a GEQ curve is displayed, the GEQ editing screen will be accessed. Note: the EQ editing screen will be accessed when the finger is removed from the curve. Swipe gestures will not cause the Editing screen to be accessed. Page 21 Yamaha Commercial Audio 5. 2 PARAMETRIC EQ EDITING LS9 StageMix V4. 0 User Guide The current channel’s Name, Color, Fader, Level Meters, [ON] and [CUE] buttons are shown in the left column. At the bottom-left, there are “previous” and “next” arrow buttons for navigating to different channels. Buttons above the channel strip section provide direct access to the Dynamics editing screen for the currently selected channel. If a GEQ is assigned to that channel, these buttons will also provide direct access to the GEQ editing screen. Navigation between these screens follows this pattern: PEQ <-> GEQ <-> DYN <-> PEQ <-> GEQ etc. . Note: the In/Out meters display the levels going In and Out of the EQ section. One band of Parametric EQ can be adjusted at a time. Press one of the green circles to select the band, and it will be highlighted yellow. EQ bands in StageMix are labelled as follows: HP = HPF (input channels only) 1 = Low Band 2 = Low-Mid Band 3 = High-Mid Band 4 = High Band Page 22 Yamaha Commercial Audio LS9 StageMix V4. 0 User Guide The current values for Freq, Gain and Q will be displayed for the currently selected EQ band. Gain and Frequency can be adjusted by dragging the circle around the graph. Q is adjusted by using the iPad’s “pinch” gesture: hold one finger (or thumb) on the screen while moving another finger closer to or further away from the first. TIP___________________________________________________________ The most comfortable and accurate way of adjusting Q is to use a vertical pinch movement with the thumb and forefinger. ______________________________________________________________ While an EQ band is being moved, the parameter value will turn yellow to indicate that it has changed. The little arrows show which direction the band should be moved to return to its previous position. In some cases, it may be necessary to adjust the gain without altering the frequency. Or to adjust the frequency without changing the gain. In this case, the “Gain Lock” or “Frequency Lock” functions can be used. These buttons are located at the top of the EQ graph. The “Lock” buttons affect all 4 bands (but not the HPF). [. . . ] StageMix will automatically attempt to reconnect to the console. If this is successful, StageMix will re-synchronize with the console data and operation will become available again. 10. 4 DHCP Server Setup on WAP/Router a) Log onto the web control page of your Wireless Access Point or Router using a web browser. c) Set the upper and lower limits of the IP addresses the DHCP server can assign. d) Ensure your console’s IP address is outside this range, or reverse its IP address (e. g. [. . . ]