User manual YAMAHA LS9EDITOR

[. . . ] LS9 Editor Owner's Manual Owner's Manual Special Notices · The software and this owner's manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Copying of the commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] You can also make these settings in the "Custom Fader Layer Setup window. " 25 LS9 Editor Owner's Manual Selected Channel window Here you can set the parameters of the currently selected input channel (INPUT CH 1­64, ST IN CH 1­4) or output channel (MIX channels 1­16, MATRIX channels 1­8, STEREO/MONO channels). You can access this window in the following ways. From the [Windows] menu, choose [Selected Channel] and select "MAIN VIEW" Double-click the channel number in one of the Overview windows On the LS9 console, assign a USER DEFINED KEY to [LS9 EDITOR CONTROL]-[SELECTED CHANNEL], and execute it NOTE By choosing [Selected Channel] from the [Windows] menu and then selecting "ADDITIONAL VIEW, " you can view a window for a channel that is not selected. This ADDITIONAL VIEW is not linked with [SEL] key operations on the panel of the LS9. The type of parameters that can be edited in this window depends on the type of the currently selected channel. The parameters of the Selected Channel window are explained below, in the order of input channels (input channels 1­ 64, ST IN CH 1­4), MIX channels, MATRIX channels, and STEREO/MONO channels. If an input channel is selected INPUT CH window 26 LS9 Editor Owner's Manual ST IN CH window NOTE Unless otherwise specified, the parameters explained below are common to INPUT CH 1­48 and ST IN CH 1­4. CHANNEL SELECT (Channel selection) 1 2 A SELECT (Channel selection) This shows the ID and name of the channel selected for operations. To switch channels, use the SELECT button or the triangle buttons at left and right. The channel selected in the Main View is linked with the [SEL] keys in the INPUT section of the LS9's panel. You can right-click the icon and select a different icon, or left-click it and select the background color. You can also edit the channel name in the text box. B INPUT PATCH Selects the input source assigned to the input channel (for the selectable input sources, p. 13). 27 LS9 Editor Owner's Manual MIX SEND 2 1 3 A MIX send level This adjusts the send level of the signal sent from the input channel to VARI-type MIX bus. The current value is shown in the numerical box immediately below. B PRE (Pre/Post) This selects PRE or POST as the point from which the signal is sent from the input channel to the MIX bus. The point will be PRE POINT when this is on, and POST FADER when this is off. The PRE POINT setting can be specified in the Mixer Setup screen. C ON (MIX send on/off) This is an on/off switch for the signal sent from the input channel to the MIX bus. HINT · If MIX buses are being used in stereo, the odd-numbered knob will be PAN. Knob of odd-numbered side · If the FIXED type is selected for the MIX bus, only the ON button is valid. · The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen. HA GAIN/Ø/HPF 1 2 3 A HA (HA Gain) Adjusts the gain of the internal head amp or of the external head amp (AD8HR) patched to the input channel. The current value is shown in the numerical box below the knob. You can set this to the default value (+10 dB) by holding down the <Ctrl> key and clicking the knob. You can also use the [48V] button to switch phantom power on/off. B Ø (Phase) Inverts the phase of the signal after AD conversion. C HPF (High Pass Filter) Use the [ON] button at the right to switch the high-pass filter on/off. You can use the knob at left to adjust the cutoff frequency. The current value is shown in the numerical box below the knob. An indication of "H" will appear on the EQ graph of the equalizer. 28 LS9 Editor Owner's Manual TO STEREO/MONO Here you can specify how the signal will be sent from the input channel to the STEREO bus / MONO bus. MODE · ST/MONO button When this button is on, the signal will be sent to the STEREO L/R bus and independently to the MONO bus. [INPUT CH 1­48] [ST IN CH 1­4] PAN (BALANCE for ST IN) Adjusts the panning of the signal sent from the input channel to the STEREO bus L/R channels. You can set this to the center position by holding down the <Ctrl> key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the LS9 panel. Switches the signal sent from the input channel to the STEREO bus on/off. Switches the signal sent from the input channel to the MONO bus on/off. ST M(C) · LCR button When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other. [INPUT CH 1­48] [ST IN CH 1­4] PAN (BALANCE for ST IN) Adjusts the panning of the signal that is sent from the input channel to each of the L/C/ R channels. You can set this to the center position by holding down the <Ctrl> key of the computer keyboard and clicking the knob. [. . . ] This value is linked with the Reverb Time value. When you change this value, the Reverb Time value changes. Drag the icon to change the value. NOTE The range is from 0 through 28. G [Diffusion] Density and spread of reverberation. Higher values increase the density and enhance the spread. [. . . ]