User manual YAMAHA M-65

[. . . ] Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. [. . . ] To reduce the TV volume level, use the remote control supplied with your TV. Press VOLUME +/­ to adjust the volume level. VOLUME 5 STB FM/XM TV PRESET/TUNE SEARCH CAT MEMORY AUTO VOL MODE SETUP INPUTMODE SLEEP 5BEAM ST+3BEAM 3BEAM 1 STEREO 2 MY BEAM 3 MY SUR. 4 MUSIC 5 MOVIE 6 SPORTS 7 OFF 8 +10 ENTRY 9 SUR. DECODE 0 ENHANCER MENU 6 CAT/ A-E DISPLAY TV/AV ENTER YSP RETURN VOLUME CH TV VOL Press SUR. DECODE and then press / ) to switch between surround modes. Signals input from 2-channel sources are played back in multi-channels. For more information on surround modes, see page 56. SUR. and Canada models) 1 Select the TV channel you want to watch. To select a TV channel, use the remote control supplied with your TV. Set the operation mode selector to YSP. TV/AV YSP or SUR. This unit outputs audio signals from your TV. TV 58 En Enjoying surround sound Adjusting surround mode parameters You can configure the parameters for Dolby Pro Logic II Music and DTS Neo:6 Music to fine-tune the surround sound effect. MUSIC MOVIE SPORTS When Dolby Pro Logic II Music is selected PANORAMA Gives the front left and right channel sound a wraparound effect, distributed throughout the entire surround sound field to give you an expansive feeling. Choices: ON/OFF Default setting: OFF DIMENSION Adjusts the difference in volume between the front and surround channels to the desired volume balance. · An error may occur if the listening room is noisy. Make sure that the listening room is as quiet as possible while the test tones are being output. · Do not shake or move the remote control while the test tones are being output. · Do not cover the My Beam microphone on the remote control while the test tones are being output. · The batteries in the remote control may be weak if the remote control does not function properly. In this case, replace all the batteries and then try the procedure again. · When the input signal with 64 kHz or 96 kHz of sampling frequency is being played back, the beam angle cannot be automatically adjusted. 1 Set the operation mode selector to YSP. TV/AV YSP 2 Press and hold MY BEAM for more than two seconds. A test tone is output twice from this unit. Keep pointing the remote control toward this unit while the test tones are being output so that the My Beam microphone can collect the test tones. Control range: L60° to R60° Operation guarantee range: 6 m (20 ft), L45° to R45° MY BEAM English 5 61 En Playing back sound clearly (My Beam) Using manual-adjust function You can adjust the beam angle manually while playing back an input source. This function is also ideal if the listening position is out of the operation guarantee range of the auto-adjust function. 1 Set the operation mode selector to YSP. TV/AV YSP 2 Press MY BEAM. [. . . ] If the menu screen does not appear, check the OSD video pin cable (see the connection example on the front page). PRESET/TUNE SEARCH A-E MEMORY The setup screen automatically changes during the AUTO SETUP procedure. When the AUTO SETUP procedure is completed, the following screen appears on the TV. INTELLIBEAM MIC SHOW RESULT MEASUREMENT COMPLETE BEAM MODE :5 BEAM SUBWOOFER :NOT APPLICABLE [ENTER]:Save set-up [RETURN]:Do not save set-up 2 Set the operation mode selector to YSP. This unit switches to the YSP operation mode. IntelliBeam microphone (supplied) Cardboard microphone stand (supplied) FM VOL MODE AUTO SETUP PREPARATION & CHECK Please connect the MIC. Please place the MIC at least 1. 8m/6ft away from the YSP unit. The MIC should be set at ear level when seated. [. . . ]