User manual YAMAHA M7CLEDITOR

[. . . ] M7CL Editor Owner's Manual Owner's Manual Special Notices · The software and this owner's manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Copying of the commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] The PRE POINT setting can be specified in the Mixer Setup screen. C ON (MIX send on/off) This is an on/off switch for the signal sent from the input channel to the MIX bus and MATRIX bus. HINT · If MIX buses or MATRIX buses are being used in stereo, the odd-numbered knob will be PAN. Knob of odd-numbered side Knob of oddnumbered side · If the FIXED type is selected for the MIX bus, only the ON button is valid. · The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen. HA GAIN/Ø/HPF 1 2 3 A HA (HA Gain) Adjusts the gain of the internal head amp or of the external head amp (AD8HR) patched to the input channel. The current value is shown in the numerical box below the knob. You can set this to the default value (+10 dB) by holding down the <Ctrl> key and clicking the knob. You can also use the [48V] button to switch phantom power on/off. B Ø (Phase) Inverts the phase of the signal after AD conversion. C HPF (High Pass Filter) Use the [ON] button at the right to switch the high-pass filter on/off. You can use the knob at left to adjust the cutoff frequency. The current value is shown in the numerical box below the knob. An indication of "H" will appear on the EQ graph of the equalizer. 25 M7CL Editor Owner's Manual TO STEREO/MONO Here you can specify how the signal will be sent from the input channel to the STEREO bus / MONO bus. MODE · ST/MONO button When this button is on, the signal will be sent to the STEREO L/R bus and independently to the MONO bus. [INPUT CH 1­48] [ST IN channel 1­4] Adjusts the panning of the signal sent from the input channel to the STEREO bus L/R channels. You can set this to the center position by holding down the <Ctrl> key of the computer PAN (BALANCE for ST IN) keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. ST M(C) Switches the signal sent from the input channel to the STEREO bus on/off. Switches the signal sent from the input channel to the MONO bus on/off. · LCR button When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other. [INPUT CH 1­48] [ST IN channel 1­4] Adjusts the panning of the signal that is sent from the input channel to each of the L/C/R channels. You can set this to the center position by holding down the <Ctrl> key of the comPAN (BALANCE for ST IN) puter keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. CSR (Center Side Ratio) Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0­100%. 26 M7CL Editor Owner's Manual EQUALIZER 1 2 3 4 7 8 5 6 9 J K A LIBRARY Accesses the INPUT EQ page of the LIBRARY window. B ON Switches the EQ on/off. C EQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the <Ctrl> key of your computer keyboard and click the graph (The HPF setting will remain). DQ E FREQUENCY F GAIN These knobs adjust the Q, center frequency, and boost/cut amount for the four bands LOW, LO-MID, HI-MID, and HIGH. G HIGH shelving If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disappear). H LPF (Low Pass Filter) If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear, and the GAIN knob will act as the low pass filter on/off switch. I LOW shelving If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear). J TYPE I/TYPE II (EQ type) Selects either TYPE I (the algorithm used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. 27 M7CL Editor Owner's Manual K ATT (Attenuation) Adjusts the amount of attenuation/gain. DYNAMICS1/2 You can select one of the following types for each of the two dynamics processors. DYNAMICS1: DYNAMICS2: GATE, DUCKING, EXPANDER, COMPRESSOR COMPRESSOR, COMPANDER-H, COMPANDER-S, DE-ESSER If GATE/DUCKING is selected 5 1 2 3 6 7 8 4 9 J K A TYPE L M Indicates the type of the currently selected gate. You can click here to select the type. B LIBRARY This button accesses the dynamics library. Clicking this button will open the DYNAMICS page of the LIBRARY window. C ON This button switches the gate on/off. D Response curve Indicates the response for the gate of the currently selected channel. E GR meter This meter indicates the amount of gain reduction. F THRESHOLD (Threshold level) Specifies the level at which the gate will open and close. The gate will open when the key-in signal exceeds this level, and will close when the signal falls below this level. G RANGE Specifies the amount by which the signal is attenuated while the gate is closed. H DECAY Specifies the time over which the gate will close after the hold time has elapsed. I ATTACK Specifies the time from when the key-in signal exceeds the threshold level until the gate opens. 28 M7CL Editor Owner's Manual J HOLD Specifies the time that the gate will remain open after the key-in signal falls below the threshold. K KEY IN SOURCE Click this to select one of the following signals to use as the key-in source. SELF PRE EQ SELF POST EQ MIX OUT 13­16 CH 1­48 POST EQ STIN1L­STIN4R POST EQ The pre-EQ signal of the currently selected input channel The post-EQ signal of the currently selected input channel The output signal of the corresponding MIX channel immediately before the output attenuation The post-EQ signal of the corresponding input channel (however, you can only choose channels belonging to the same group, within the seven groups CH1­8, CH9­16, CH17­24, CH25­32, CH33­40, CH41­48, and STIN1L­STIN4R). L CUE This button cue-monitors the currently selected key-in signal. This is not shown in the ADDITIONAL VIEW. M KEY IN FILTER Select the type of filter applied to the selected key-in signal; HPF (high pass filter), BPF (band pass filter), or LPF (low pass filter). The ON/OFF button switches the filter on/off. If you've selected BPF, use the two knobs to adjust the band pass frequency and Q. [. . . ] 70 FADE TIME page . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 FADING ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . 69 FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 65 File Close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]