User manual YAMAHA MAGICSTOMP SE

[. . . ] Sound Editor for MAGICSTOMP · · · · · · · · · Copying of the commercially available music sequence data and/or digital audio files is strictly prohibited except for your personal use. The software and this owner's manual are exclusive copyrights of Yamaha Corporation. Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] 4 Files of type: . . . . . . . . . . Click this and choose the file type (. UB9). 5 [Open] button. . . . . . . . . Click this to open the file selected from the List. 6 [Cancel] button . . . . . . Click this to cancel the operation. 14 2 "Save" button Click this to save the existing Library file with your new settings. If you are working on a new file, this button will open the "Save As" dialog, where you can name and save your settings as a new Library file (*. UB9). "Save As" Dialog 1 2 3 4 5 6 n If you are using a Macintosh, the typical Macintosh "Save As" dialog will appear. 1 Save in:. . . . . . . . . . . . . . . . . . . Click this and choose the folder in which to save the Library file. 2 List box. . . . . . . . . . . . . . . . . . . Shows the contents of the folder you wish to save to. 3 File name:. . . . . . . . . . . . . . . Specify the name of the Library file to be saved here. 4 Save as type:. . . . . . . . . . Click this and choose the file type. 5 [Save] button. . . . . . . . . . Click this to save the Library file with the name specified in the "File name" field. 6 [Cancel] button . . . . . . Click this to quit the dialog without storing. n If you save a file to a Macintosh computer, the extension ". UB9" is not added automatically. 15 3 "Editor Setup" button Click this to open the "Setup" dialog and specify the MIDI port settings. "Setup" Dialog These settings let you transmit and receive patch data between the MAGICSTOMP and the computer. Click the [OK] button to apply the settings and quit the dialog. Click the [Cancel] button to quit without applying the settings. * Bulk Transmit: Data in the computer is transmitted to the MAGICSTOMP. * Bulk Receive: Data in the MAGICSTOMP is downloaded into the computer. Windows Macintosh 1 2 3 4 5 6 3 4 5 1 MIDI In Port: . . . . . . . . . . . Click this and choose the MIDI In port. You can use the Sound Editor to receive data sent from the MAGICSTOMP connected to this port. n If you are using a Macintosh, the MIDI In Port setting is assigned in the OMS Port Setup. (page 11). 2 MIDI Out Port: . . . . . . . . Click this and choose the MIDI Out port. You can use the Sound Editor to control and edit the MAGICSTOMP connected to this port. n If you are using a Macintosh, the MIDI Out Port setting is assigned in the OMS Port Setup. (page 11). 3 MIDI Ch: . . . . . . . . . . . . . . . . . . Sets the MIDI transmit/receive channels for transferring data between the MAGICSTOMP and the computer. 4 Device No. : . . . . . . . . . . . . . This number is used when transmitting/receiving system exclusive data (bulk transmit/receive). 5 Dump Interval: . . . . . . . Click this and choose the interval between successive MIDI dumps. n If errors occur while transferring data, set this value to a higher number. 6 Export to Host: . . . . . . This function is not available with the MAGICSTOMP. 16 4 "Transmit" button Click this to open the "Transmit" dialog to transmit all settings to MAGICSTOMP. "Transmit" Dialog Transmits the entire contents in the User Patch library window (001-099) to the MAGICSTOMP. Click the [Start] button to begin transmitting the data. The progress bar shows how much of the data has been transmitted. Finally, click the [Close] button to quit the dialog. 1 2 3 4 1 Transmit Type . . . . . . . . . Indicates the patch data to be transmitted. This setting is fixed to "User" with the MAGICSTOMP. 2 Progress bar . . . . . . . . . . Indicates how much of the data has been transmitted. [. . . ] The cursor is highlighted and you can enter characters for the name. Enter the Patch name via the keyboard of your computer. n Patch names can consist of up to 12 characters. Click the Memory box and choose the Memory in which to store your edited patch. This setting is fixed to "User" with the MAGICSTOMP. 23 4 In the Patch Name list, click the patch in which your edited patch will be stored. n After storing to a Library file, the data for the original patch will be overwritten when you save the Library file. It is recommended that you back up important data. 5 Click the [Store] button to store your edited patch in the location specified in step #4. n The "Store" dialog is used to temporarily store your Library file. [. . . ]